Krups EA9000 Serie Manual Del Usuario página 26

KRUPS
SERIE EA9000
PROBLEM / MALFUNCTION PROBABLE CAUSES
The machine may need to run a
n
cleaning cycle.
The coffee is not creamy.
The coffee is not fresh enough.
n
The coffee grinder makes a Foreign bodies are inside the
n
strange noise. grinder.
The nozzle or the nozzle support is
n
blocked.
No steam comes out of the nozzle.
The water used is not suitable for
n
making steam.
The steam does not come out
n
properly.
There is not enough milk froth.
The milk is not cold enough.
n
The steam does not come out
n
properly.
The milk froth is not fine enough.
The milk is not suitable.
n
46
CORRECTIVE ACTIONS
Start a cleaning of the machine
n
(see section 8).
Try using fresher coffee beans /
n
grounds.
Check whether you can extract the
n
foreign body using a tool. Unplug
the machine before you do this.
Contact the KRUPS Customer
n
Service.
Wash the steam nozzle manually
n
(see section 8); clean and unblock
each part.
Check that the steam nozzle is
n
screwed on properly.
Empty the tank and remove the
n
Claris cartridge temporarily.
Fill the water tank with mineral
n
water with high calcium content
(>100 mg/l) and carry out steam
cycles (5 to 10) consecutively into
a recipient until you get a
continuous jet of steam.
See paragraph above.
n
We recommend that you use cold
n
pasteurised or UHT milk, freshly
opened.
Check that the milk is fresh and
n
cold.
Check that there is enough milk in
n
the glass.
Wash the steam nozzle manually
n
(see section 8); clean and unblock
each part.
Check that the steam nozzle is
n
screwed on properly.
We recommend that you use cold
n
pasteurised or UHT milk, freshly
opened.
PROBLEM / MALFUNCTION PROBABLE CAUSES
No cleaning liquid.
Nozzle cleaning does not take
n
place properly.
The milk used is not suitable.
n
The water tank is not fitted
n
properly.
The water tank has been filled,
but the warning message is still The float at the bottom of the tank
n
displayed on the screen. does not move freely.
The water tank is scaled up.
n
The drip tray has been emptied,
but the warning message is still The metal contacts are dirty.
n
displayed on the screen.
The used coffee collector is not
The used coffee collector has
n
been emptied, but the warning fitted properly.
message is still displayed on the
The used coffee collector has
n
screen.
been fitted back too quickly.
A power failure occurs during
the cycle.
There is water underneath the The drip tray is not correctly fitted
n
appliance. or is overflowing.
!
Note:
Programming problems are often resolved by unplugging the appliance for about one minute and
then plugging it in again.
Danger: Only a qualified technician is authorised to carry out repairs on the power cord and the
220 - 240V electrical system. Failure to respect this exposes you to fatal injuries due to
the presence of electricity! Do not use an appliance that is visibly damaged!
ENGLISH
CORRECTIVE ACTIONS
Check that your preparation does
n
not boil while heating or frothing.
If it does, reduce the heating
and/or frothing time.
Check that the cleaning liquid
n
bottle is not empty.
Carry out a manual cleaning.
n
We recommend that you use cold
n
milk.
Check and unblock the float if
n
necessary.
Reinstall the water tank properly
n
until you feel some resistance.
Rinse the water tank under
n
running water and descale, if
necessary.
Clean and wipe the metal
n
contacts at the back of the drip
tray.
Refit the used coffee collector.
n
Wait for at least 8 seconds before
n
refitting the empty collector.
The appliance is automatically
n
reinitialised when it is switched
back on.
Check that the drip tray has been
n
fitted correctly and empty it if
required.
47