Tabla de contenido
Idiomas disponibles
Idiomas disponibles
DANGER: Improper connection of the equipment grounding conductor can result in a risk of electric shock. The conductor
with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor.
If repair or replacement of the cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to
whether the worklight is properly grounded. Do not modify the plug connected to the worklight—if it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
FOR GROUNDED, CORD-CONNECTED WORKLIGHTS RATED LESS THAN 15A AND INTENDED FOR USE ON A NOMINAL
120V SUPPLY CIRCUIT
The worklight is for use on a nominal 120V circuit,
and should be connected to a grounding plug that
looks like the plug illustrated in sketch a. A
temporary adaptor, which looks like the adaptor
illustrated in sketch b, may be used to connect this
plug to a 2-pole receptacle as shown in sketch b if
a properly grounded outlet is not available. The
temporary adaptor should be used only until a
properly grounded outlet can be installed by a
qualified electrician. The green colored rigid ear, lug, and the like, extending from the adaptor must be connected to a
permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by
the metal screw.
IN CANADA, THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN ELECTRICAL CODE. Make sure
that the appliance is connected to an outlet having the same configuration as the plug. No adapter should be used with this
appliance.
Use of Extension Cords with Worklight
Only use a grounded extension cord that is rated at least 12 amps and has a third-wire ground. When a long extension cord is used
to connect a worklight or tool, a voltage drop occurs. The longer the cord, the greater the voltage drop. This results in less voltage
being supplied to the worklight or tool and increases the amount of current (amp) draw or reduces performance. A heavier cord
with a larger wire size will reduce the voltage drop. Be sure to choose a cord that will supply enough voltage to operate your tool
and/or worklight. The table below indicates appropriate gauge for extension cords.
WARNING:
Keep electrical cords in good condition. Do not use worn, bare, or frayed cords because they can cause electrical shock.
WARNING:
Operating equipment at low voltage can cause it to overheat. Using an excessively long extension cord can cause the
cord to overheat.
Minimum Gau ge for Extension Cord Se ts
Volts
Total Length of Co rd in Feet (meters)
Ampere Rati ng
120V
25 (7.6)
240V
50 (15.2)
More
Not More
Than
Than
0
6
18
6
10
18
10
12
16
CARE AND MAINTENANCE
WARNING:
Always make sure that the work light is unplugged and cooled down before attempting to clean it.
• Clean the lamp head, lens cover, and lamp stand regularly with a non-abrasive cleaner.
• Allow the work light to cool down completely before storing.
• Store in a safe place, out of the reach of children.
WARRANTY
If this product fails due to a defect in materials or workmanship within five (5) years from the date of purchase, return it along
with proof of date of purchase and it will be replaced with the same or comparable model free of charge. This warranty is void
if damage or defect has resulted from accident, abuse, misuse or faulty repair. This warranty gives you specific legal rights and
you may have other rights that vary from state to state.
All product warranties are covered by Lutec USA LLC.
a
b
GROUNDED
OUTLET
BOX
GROUNDING PIN
ADAPTER
50 (15.2)
100 (30.5)
150 (45.7)
100 (30.5)
200 (61.0)
300 (91.4)
AWG
16
16
14
16
14
12
16
14
12
4
IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL OR INDIRECT DAMAGES OF ANY KIND
ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.
SPECIFICATIONS
Watts:
17W
Lumens:
1500lm
Color temperature:
4000K
Use environment:
Wet location
Voltage:
120VAC
© 2019 Stanley Black & Decker, Inc.
STANLEY® and the STANLEY Logo are trademarks of Stanley Black & Decker, Inc. or one of its affiliates, and are used under license.
If this product ever fails, Lutec USA LLC. will replace it. DO NOT RETURN PRODUCT TO STORE.
Simply call 1-877-714-8669 toll-free, 8:30 a.m. - 5:00 p.m. ET(Enter correct times and contact dates), Monday-Friday (Contact Email:
Please note: Calls made from outside the US will be charged international rates & 1-(704)980-4135.
www.stanleytools.com
www.stanleyledlighting.com
5
Tabla de contenido
