Set Up - Panasonic PT-47WXD63 Instrucciones De Operación

Set Up

This menu lets you select antenna, program channels,
select analog and digital closed caption, Convergence,
Auto Power On, Image Shift and Zoom Adjust.
Procedure
• Press MENU to display the Main Menu.
• Press CH, CH ,
Setup icon.
• Press OK button to display the options in the Setup
menu.
Program CH
This menu allows you set up the antenna, auto scan all available
analog and digital channels, manually add or delete channels and
display the signal strength of the digital channels.
Input Setup - Lets you specify Antenna mode (Cable
only, Cable/Antenna or Antenna only).
Note: You can connect either a Cable antenna or a terrestrial
antenna to Ant A. However, if you have both Cable signal
and terrestrial antenna signal, the Cable signal must be
connected to the Ant A input on the back of the
projection television. Connect the antenna signal to the
Ant B input.
Procedure
• In Set Up menu, select Program Channel and press OK.
• Press OK to enter sub-menu. Press
select Cable Only, Cable/Antenna or Antenna Only.
• Press OK button to enter your selection. When the next
screen will be displayed, press OK button to start the
Auto scan. Auto scan must be done when you select the
input signal for the first time or whenever you change the
antenna configuration.
Program Channel
Input Setup
Cable only
Auto Scan
Connect Cable to Antenna (A)
Manual Program
Signal Meter
Change your Input Setup
and press OK
Program Channel
Input Setup
Cable only
Auto Scan
Connect Cable to Antenna (A)
Manual Program
Signal Meter
Auto scan is needed
press OK to start Auto Scan
Notes:
• If Cable Only, Antenna Only or Antenna/Cable is
selected and DCM (Digital Cable Module) is not in, the
Auto scan will perform Scan All.
VOL or VOL to select the
VOL or VOL
OK
OK
• If Cable Only is selected and DCM is in, Auto scan will
be skipped.
• If Cable/Antenna is selected and DCM is in, Antenna (B)
Analog & Digital Auto scan will be performed.
Auto Scan - To automatically Scan All available
channels, Antenna (A) Analog, Antenna (A) Analog &
Digital, Antenna (B) Analog and Antenna (B) Analog &
Digital.
Procedure
• Highlight Auto Scan and press OK to enter the sub
menu.
• Use CH and CH
auto scan. After Auto Scan is completed press MENU to
return to the previous screen.
Program Channel
Input Setup
Auto Scan
Manual Program
Signal Meter
Manual Program - To add or delete channels from
either channels list (A/B) manually.
Program Channel
Input Setup
RF Input
Channel Add
Auto Scan
Channel Delete
Manual Program
Signal Meter
Signal Meter - Displays the signal strength of the ATSC
digital channel in either Antenna (A) or Antenna (B).
Note: Signal meter feature is not available for analog channels.
to
Procedure
• Highlight Signal Meter and press OK button to enter the
sub-menu.
• In the RF Input field, select either Antenna (A) or
Antenna (B).
• Select the channel number using
buttons.
• Press OK button to display the Signal Strength.
Program Channel
RF Input
Input Setup
RF Channel
Auto Scan
Manual Program
Signal Meter
Note: The color of the signal bar usually indicates the strength
of the received signal.
• Green - Adequate signal for a good reception.
• Yellow - Poor signal strength.
• Red - Very poor signal strength.
M O
ENU PERATIONS
to select and press OK to start the
Scan All
Antenna (A) Analog
Antenna (A) Analog & Digital
Antenna (B) Analog
Antenna (A) Analog & Digital
Press OK to channel scan
all available channels
SELECT
Antenna (A)
MENU
to return
A: 12
VOL or VOL
Antenna (A)
________
3-1
Signal Strength: 70%
Peak: : 75%
OK
OK
EXIT
25