Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
2. Ensure foam filter
15
dry. Rinse and wash as necessary.
3. Rinse and wash pre-filter
4. Rinse and wash collection tank
nOTE: Collection tank
washer safe (top rack only).
5. Ensure all components are completely dry before
re-assembling.
6. Once cleaning is finished, insert foam filter
the pre-filter
16
.
7. Install the pre-filter
16
close and latch the tank, and install it back onto the
main body
3
.
nOTE: Ensure pre-filter
tank
8
by gently tugging on pre-filter
filter
16
. is loose, fully press the pre-filter
collection tank
8
until it snaps into place.
Fig. M
8
Cleaning Chute & Nozzle Cover (Fig. N)
CAUTION:
chute
17
are top rack only, dish washer safe. It is
recommended that you manually rinse the nozzle
cover
18
and chute
top rack of the dishwasher.
1. Remove the chute
17
the retention button slightly. Then pull the nozzle cover
18
away from the main body
2. The nozzle cover
18
17
to rinse and wash each component.
3. The nozzle cover
18
(top rack only).
4. Ensure the chute
17
before re-assembling.
5. Once cleaning is finished, attach nozzle cover
the chute
17
and insert into the assembly into the front
of the main body
3
.
nOTE: Ensure the top clip of the nozzle cover
snaps into place onto the chute
extra pushing force.
8
inside the pre-filter
16
16
as necessary.
8
as necessary.
8
and pre-filter
16
are dish
15
into the collection tank
16
. is fully sealed to collection
16
.. If pre-
8
into the
15
16
11
Nozzle cover
18
and
17
before placing them in the
and nozzle cover
18
by pulling
3
.
can be lifted away from the chute
and chute
17
are dish washer safe
and nozzle cover
18
are dry
17
. This may require
is still
Fig. N
17
18
into
8
,
Storage (Fig. A, B)
1. Ensure main body
2. Empty fluid tank of all chemicals. Wash with warm clean
water and dry the formula dispenser tank
17
and nozzle cover
emptied and cleaned to reduce dirt build up.
3. Check if charging is required by pressing the state of
charge indicator button
handle
to charging socket
4. Store main body
5. Store main body
level surface and switch
6. Store out of reach of children or pets.
TROUBLESHOOTING
If the product does not work, check the following:
•
The charger was correctly plugged in for recharge. (It
feels slightly warm to the touch.)
•
The charger cord is not damaged and is correctly attached.
•
The charger is plugged into a working electrical outlet.
•
The switch is in the "OFF" position when charging.
For assistance with your product, visit our website
www.blackanddecker.com for the location of the service
center nearest you or call the BLACK+DECKER help line at
1–800–544–6986.
ACCESSORIES
Recommended accessories for use with your appliance are
available from your local dealer or authorized service center.
If you need assistance regarding accessories, please call:
1-800-544-6986.
WARNING:
recommended for use with this appliance could be
hazardous.
18
onto
SERVICE INFORMATION
All BLACK+DECKER Service Centers are staffed with trained
18
fully
personnel to provide customers with efficient and reliable
power tool service. Whether you need technical advice,
repair, or genuine factory replacement parts, contact the
BLACK+DECKER location nearest you. To find your local
3
3
is turned OFF.
18
. Ensure collection tank
22
at the back of the main
2
. If charge is required, plug in the jack plug
5
and allow the appliance to charge.
3
in a cool, dry area.
3
with the collection tank
1
facing up.
The use of any accessory not
6
, chute
8
is
21
8
on a flat
Tabla de contenido
