Tabla de contenido
Idiomas disponibles
Idiomas disponibles
INSTALLATION INSTRUCTIONS
E-FCB and E-FFB Series
MOUNTING USING 2" FITTER (E-FFB18 AND
E-FFB23)
NOTE: fixture is intended to be mounted on 2-3/8" (60 mm) O.D. heavy
wall pipe or tenon.
1.
Remove splice compartment cover from upper fitter by removing
(2) screws on cover.
2.
Route supply leads through bottom of the fitter and into fitter splice
compartment.
3.
Strain relief is required for electrical connections on 2" adjustable
fitter mounts at heights of 35' (7.6 m) and above. Tie a knot in the
supply wires above the supply wire entry hole in the fitter splice
compartment to reduce the strain on the connections. Make sure
the knot will not slip through the hole.
4.
Slip lower fitter over the mounting pipe or tenon, being careful not
to pinch any leads.
5.
Aim fixture by rotating on pipe or tenon to desired direction.
Securely tighten (2) Allen set screws on fitter to 140 in-lbs
(16 N•m).
6.
Loosen (DO NOT remove) Allen head bolt holding two halves of
fitter together. Tilt fixture to desired angle. Tighten bolt to
132 in-lbs (15 N•m).
7.
Wire in splice compartment as indicated in Electrical
Connections section.
8.
Replace fitter splice compartment cover and tighten (2) screws
that were removed in Step 1.
ELECTRICAL CONNECTIONS
Fixture is equipped with universal volt driver 120-277V
(ie. 120V, 208V, 240V or 277V)
PHASE TO NEUTRAL WIRING 120/277V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply common to fixture neutral (white) lead.
3. Connect supply Vin to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no
wires are pinched.
PHASE TO PHASE WIRING 208/240V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply L1 (Hot) to fixture neutral (white) lead.
3. Connect supply L2 (Hot) to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no
wires are pinched.
www.e-conolight.com
|
Document:
LPN00548X0001A2_A
Created By:
TMT
CAUTION: Changes or modifications not expressly approved
could void your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved could void
your authority to use this equipment.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
CAN ICES-005 (B)/NMB-005 (B)
888.243.9445
|
FAX: 262.504.5409
Date
ECO#
FCC NOTICE
7-02-2019
010778
Tabla de contenido
