Tabla de contenido
Idiomas disponibles
Idiomas disponibles
INSTALLATION INSTRUCTIONS
E-HTH Series
HOOK AND CORD MOUNTING
1.
Loosen retaining screw on hook to allow hook to engage eye bolt
(supplied by others) attached to mounting surfaces. After engaging
hook onto eye bolt, retighten retaining screw to prevent hook from
coming off eye bolt. See Figure 3.
NOTE: Make sure eye bolt and supporting structure have
appropriate weight ratings to support weight of fixture (20 lbs).
2.
Splice fixture cord leads to supply leads in junction box per
Electrical Connections section. For dimming applications,
second cord with grey and violet leads will also be used.
INSTALLATION OF PENDANT MOUNT ACCESSORY
Loosen set screw holding hook in place. See Figure 3.
1.
2.
Unscrew hook form threaded connection on top of fixture. Discard
hook and retain lockwasher.
3.
Place lockwasher on male threaded shaft of pendant mount
accessory.
4.
Screw pendant mount accessory into threaded opening on top of
fixture. Turn pendant mount accessory with torque sufficient to
compress lockwasher.
5.
Tighten set screw loosened in Step 1.
PENDANT MOUNTING-
Requires use of Pendant Mount Accessory
1.
Thread pendant mount accessory, previously installed onto fixture
as detailed above in INSTALLATION OF PENDANT MOUNT
ACCESSORY, onto threaded end of 3/4" pendant.
NOTE: Make sure pendant and attachment point to structure have
the appropriate weight ratings to support weight of fixture (20 lbs).
2.
Tighten set screws on Pendant Mount Accessory to secure fixture
to pendant.
3.
Splice fixture cord leads to supply leads in junction box per
Electrical Connections section. For dimming applications,
second cord with grey and violet leads will also be used.
FIGURE 3
Set Screw
Retaining
Screw
www.e-conolight.com
|
Document:
LPN00616X0001A0_A
Created By:
TMT
ELECTRICAL CONNECTIONS
Fixture is equipped with universal volt driver 120-277V
(ie. 120V, 208V, 240V or 277V)
PHASE TO NEUTRAL WIRING 120/277V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply common to fixture neutral (white) lead.
3. Connect supply Vin to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no
wires are pinched.
PHASE TO PHASE WIRING 208/240V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply L1 (Hot) to fixture neutral (white) lead.
3. Connect supply L2 (Hot) to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no
wires are pinched.
DIMMING
1. Grey and violet leads are for 0-10V dimming systems.
Cap off if not used.
2. For dimming connections, use Class 1 wiring methods.
CAUTION: Changes or modifications not expressly approved could void
your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved could void your
authority to use this equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-005 (B)/NMB-005 (B)
888.243.9445
|
FAX: 262.504.5409
Date
ECO#
FCC NOTICE
10-22-2018
009785
Tabla de contenido
