Pressure And Capacity Data; Installation And Maintenance; English - SPX Johnson Pump Manual Del Usuario

Ocultar thumbs Ver también para Johnson Pump:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26

Pressure and capacity data

(based on water at +20°C/68°F and
at full voltage of the motor)
WD 3.4
Pressure
Bar
kPa
psi
0
0
0
0,5
50
7,3
1
100
14,5 10,9
1,5
150
21,8 10
2
200
29
2,5
250
36,3 8,3
3
300
43,5 7,5
3,5
350
50,8 6,8
4
400
58
4,5
450
65,3 5,3
5
500
72,5 4,5
Fuse required
WD 5.0
Pressure
Bar
kPa
psi
0
0
0
0,5
50
7,3
1
100
14,5 16,6
1,5
150
21,8 15,5
2
200
29
2,5
250
36,3 13,4
3
300
43,5 12,4
3,5
350
50,8 11,4
4
400
58
4,5
450
65,3 9,7
5
500
72,5 8,7
Fuse required

Installation and maintenance

Installation
Locate the pump in a dry location.
If the pump is mounted vertically, the
motor shall face up.
Mark screw positions and drill pilot holes
(see drilling template page 45).
Mount the pump using stainless steel
screws taking care not to over compress
the vibration dampening rubber feet.
Reinforced, high pressure flexible tubing
is recommended.If rigid pipe is used, a
length (225 mm/9 inches minimum) of
flexible tubing shall be installed between
the pump and the rigid pipe. This will
Original instructions
Flow
Amp. draw
l/min
USGPM 12 V
13
3,4
2,3 A
12,1
3,2
3,3 A 1,4 A
2,9
4,5 A
2,6
5,5 A 2,5 A
9
2,4
6,4 A 2,8 A
2,2
7,2 A 3,2 A
2,0
8,1 A 3,6 A
1,8
8,9 A
6
1,6
9,7 A 4,4 A
1,4
11 A 4,8 A
1,2
11 A 5,1 A
15 A
Flow
Amp. draw
l/min
USGPM 12 V
18,9
5
3,6 A
17,8
4,7
5 A
4,4
6,6 A
4,1
7,8 A
14,5
3,8
9,1 A
3,5
10,4 A
3,3
11,7 A
3
13 A
10,6
2,8
13,8 A
2,6
14,8 A
2,3
15,9 A
20 A
address noise and/or damage caused by
vibration transmitted to rigid pipe.
Use stainless steel hose clamps to secure
tubing to quick disconnect fittings and
other hose barbs in the system.
The strainer that follows the pump must
be installed in line before the pump intake,
24 V
to prevent debris from entering pump
1 A
and interfering with proper functioning of
valves.
2 A
Electrical installation
The pump must be installed according to
ISO 10133 (Small craft – Electrical system
4 A
– Extra low voltage DC installation for
continuous current). Note: The fuse must
be ignition protected.
The motor is equipped with built in ther-
8 A
mal protection to prevent the motor from
overheating. The protection is automatically
restored when the motor is cooled.
If the pump is connected with separate
earth lead, this should be yellow/green and
24 V
connected to the motor base.
1,7 A
See the wiring table (next page) for
2,4 A
correct installation. Negative wire must
3 A
be black.
3,6 A
4,2 A
Choose wire size in accordance with
4,8 A
total wire lenght (see table next page).
5,2 A
The wire connections must be sealed with
5,7 A
6,2 A
a marine sealant.
6,5 A
Note: Before installation with electrical
7 A
control systems, check that equipment
10 A
to be used is of sufficient rated capacity
to accept amperage draw of motor. Low
voltage will cause motor to overheat.
> English
9
Tabla de contenido
loading

Tabla de contenido