Eaton ALL PRO WLT5040LST Instrucciones

WLT5040LST
ENGLISH
IITEMS REQUIRED
(Purchase separately)
• Adjustable wrench
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK,
EXPOSURE TO EXCESSIVE UV RADIATION, OR INJURY TO PERSONS.
WARNINGS AND CAUTIONS
WARNING: When using outdoor use portable luminaires, basic safety precautions
should always be followed to reduce the risk of fire, electric shock, exposure to exces-
sive UV radiation or injury to persons.
WARNING: To reduce the risk of fire, electric shock, exposure to excessive UV radiation
or injury to persons.
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Your LED fixture is prewired. No replacement bulb necessary. Disassembling your
fixture will void the warranty.
• The worklight should be located no further than 6 feet from the nearest outlet.
WARNING
• Risk of fire/electric shock.
• The electrical system, and the method of electrically connecting the fixture to it, must be in
accordance with the National Electrical Code and local building codes.
• Do not look directly at lighted lamp.
CAUTION
READ ALL INSTRUCTIONS
• For indoor and outdoor use.
• cULus LISTED for wet locations.
• Connect fixture to a 120-volt, 60 Hz power source. Any other connection voids
the warranty.
• Use with only three-wire outdoor extension cords that have three-prong grounding
plugs and grounding receptacles that accept the appliance's plug, such as an
extension cord of cord type: SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A,
SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, SJTOW, SJTOW-A.
• Ground Fault Circuit Interruption (GFCI) protection is to be provided on the circuit(s)
or outlet(s) to be used for the wet location portable luminaire. Receptacles are
available having built-in GFCI protection and are able to be used for this measure
of safety.
• This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 [email protected]
PACKAGING CONTENTS/ CONTENIDO DEL PAQUETE
A. (2) Light heads
(2) Cabezas de la
lámparas
(2) Têtes de luminaire
B. Sled crossbar
Barra transversal
tipo trineo
Barre transversale du
traîneau
C. Quick-release knob
Perilla de liberación
rápida
Bouton de déverrouillage
rapide
Instruction Manual / Manuel d'instructions/ Instrucciones
D. Center handle
Manija central
Poignée centrale
E. (2) Light handles
(2) Manijas de la lámpara
(2) Poignées du luminaire
F. Light bracket
Abrazadera de la lámpara
Support du luminaire
G. Tripod stand
Soporte del trípode
Trépied
frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user's authorization to operate this equipment.
SAVE THESE INSTRUCTIONS AND WARNINGS.
ASSEMBLING YOUR FIXTURE
WARNING: Deviation from the assembly
instructions may result in a risk of fire or
electric shock.
1. To mount handle use Qty (2) M6 x
28mm hex head screws (I) and attach
handle (D) to the sled crossbar (B) (Fig. 1).
2. To mount light fixture (A) to the sled crossbar
(B), screw M6 x 25mm machine screw with knob,
through the hole in the light bracket (F), through
the hole on the sled crossbar (B) until secure.
Repeat for the other light fixture head (Fig. 2).
1
H. (2) M6 x 25mm Machine Screw with Knob
(2) Tornillos de máquina M6 x 25 mm
con manija
(2) Vis de mécanique M6 de 25 mm
avec bouton
I. (2) M6 x 28mm Hex Head Machine Screw
(2) Tornillos de máquina hexagonales
M6 x 28 mm
(2) Vis de mécanique à tête hexagonale
M6 de 28 mm
1
D
2
A
H
B
B