Before Using For The First Time; Preparing The Filter Coffee - FAR EC-15 CI Manual De Instrucciones

ENGLISH

BEFORE USING FOR THE FIRST TIME

To guarantee the flavour in your first cup of coffee,
you need to rinse the coffee maker with hot water as
follows:
Open the water tank lid and pour water into the
1.
tank, ensuring that you follow the gauge levels.
Insert the nylon filter into the filter holder (without
2.
the ground coffee). Then close the water tank lid.
Insert the steel filter into the metal filter holder (without the ground coffee). Then
3.
insert the filter holder into the appliance in the position and fasten it firmly onto
the appliance by turning it anti-clockwise until it is in the position (Image 1).
Place the coffee pot onto the hot plate and place an espresso cup (your cup) onto
4.
the removable grille. Check that the steam knob is in the "OFF" position.
Plug in the appliance; "12:00" is displayed on the screen.
5.
Press the left button twice for the filter coffee function; the red light comes on
6.
and hot water starts to flow after several seconds.
After several minutes, press the button again. The red light goes out and the
7.
coffee maker switches off.
Press the right button for the espresso function. The red light comes on and the
8.
green light flashes. This is the default programme. Press the
the water into the boiler first. When the water starts to flow, press the
and switch off the pump immediately. The internal heating element comes on and
the coffee maker pre-heats. When the green light stops flashing and remains on,
pre-heating is finished. Press the
Note: The pump can only pump water when the green
on. This means that when the green
is inactive.
When no more water flows out, empty out the water in each container and clean
9.
them gently. You can now begin making the coffee.
Note: There might be some noise the first time that the pump pumps the water.
This is normal, as the appliance is expelling internal air. The noise ceases after
approximately 20 seconds.
GB-6
Image 1
button to pump
button
button again and the water begins to flow.
light flashes or remains
light flashes or remains on, the button

PREPARING THE FILTER COFFEE

Function light (red)
Timer light (orange)
Program button: Set the current time or
Set the minutes
automatic start time.
Set the hour
On button
Open the water tank lid and pour water into the tank, ensuring that you follow the
1.
gauge levels.
Note: The water level must be between the lowest and highest markers.
Insert the nylon filter into the filter holder and put the ground coffee into the
2.
filter using the measuring spoon. One spoon of ground coffee is generally enough
for one cup of coffee but you can modify the amount of coffee depending on your
preferences. Close the water tank lid.
Place the coffee pot onto the hot plate, aligning its central line with that of the brew
3.
basket.
Plug in the appliance; "12:00" is displayed on the screen.
4.
Press the button twice for the filter coffee function; the function light comes
5.
on and the appliance begins to work. The coffee flows out automatically after a
moment.
Note 1: You can remove the coffee pot at any time to serve coffee but replace it
within 30 seconds.
Note 2: The appliance switches off automatically 30 minutes after the start of the
coffee brewing cycle.
Once brewing is finished, remove the coffee pot and serve the coffee
6.
(approximately one minute after the coffee stops flowing).
Note: The amount of coffee that is brewed is less than the amount of water poured
into the tank, as part of the water is absorbed by the ground coffee. For safety
reasons, we recommend that you close the coffee pot lid when you pour the coffee;
this also helps it to stay hot.
The coffee maker switches to keep warm mode when brewing is finished.
7.
Always switch off the coffee maker and always disconnect its power cable from the
8.
mains when you are not using the coffee maker.
Note: Take care when pouring the coffee, as it is very hot just after the end of the
brewing cycle and could burn you.
ENGLISH
GB-7