Black+Decker BDCMTO Manual De Instrucciones página 23

f Grasp the tool and squeeze the accessory clamping
lever as shown in Fig.B.
f Clean any residual debris from the tool shaft and the
accessory holder.
f Slide the accessory into the accessory holder making
sure the accessory engages all eight pins on the
holder and is flush with the surface of the holder.
f Release the accessory clamp lever.
f Some accessories, such as scrapers and blades can
be mounted at an angle if required as shown in Fig.C.
Plunge cutting - Fig. D
Warning! Hold saw firmly with both hands for all cutting
operations.
Warning! Inspect work area for hidden electrical wiring,
gas pipes or water pipes before making blind or plunge
cuts. Failure to do so may result in electrical shock, fire,
explosion, or property damage.
Warning! Always use safety glasses. Everyday
eyeglasses are not safety glasses. Also use face or dust
mask if cutting operation is dusty. Always wear certified
safety equipment.
Warning! Cut hazard. Before cutting any type of
material, be sure it is firmly anchored or clamped to
prevent slipping.
Warning! Cut hazard. Let the tool work at its own
pace. Do not overload, blade breakage may occur.
Warning! Cut hazard. This tool has no provision to lock
the switch in the ON position, and should never be locked
in the ON position by any other means.
To make a cut:
f Clearly mark the desired cutting area.
f To switch the tool on, pull the variable speed trigger
on the power unit. The tool speed depends on how far
you pull the trigger.
f Switch the tool on before applying pressure and
slowly feed the plunge cut blade into the workpiece at
the marked location.
Warning! Cut hazard. Ensure the blade is not in
contact with cutting surface before starting saw.
f Advance the blade along the cutting line until cut is
completed. Don't force the tool; let the blade cut at its
own speed.
f To switch the tool off, release the trigger.
Note: Always use the appropriate type of saw blade for
the work piece material and type of cut. Cut only with
sharp blades; they cut cleaner, faster and put less strain
on the motor while cutting.
Sanding
Warning! Fire hazard. When working on metal
surfaces, do not use a vacuum cleaner because sparks
are generated. Wear safety glasses and a dustmask.
Due to the danger of fire, do not use your sander to sand
magnesium surfaces. Do not use for wet sanding.
f To switch the tool on, pull the variable speed trigger
on the power unit. The tool speed depends on how far
you pull the trigger.
f To switch the tool off, release the trigger.
Note: Do not rest fingers on platen during use. Move it
in long sweeping strokes across the surface, letting it do
the work. Light pressure is all that is required for sanding.
Excessive pressure will slow the tool and produce inferior
results. Check your work often, product is capable of
removing material rapidly. Excessive force will reduce the
working efficiency and cause motor overload. Replacing
the sanding sheet regularly will maintain optimum working
efficiency.
Note: Always ensure the workpiece is firmly held or
clamped to prevent movement. Any movement of the
material may affect the quality of the sanding finish.
Installing/removing sanding sheets (Fig. E)
A diamond shaped platen uses a hook and loop adhesion
system to attach the sanding sheets. The platen allows you
to use it on large flat surfaces and tight spots or corners.
f Attach the sanding platen as described under
"Installing/Removing Accessories."
f Align the edges on the sanding sheet, with the edge
of the sanding platen and press the sanding sheet
onto the platen.
f Firmly press the base with the sanding sheet attached
against a flat surface and briefly switch the tool on.
This provides for good adhesion between the platen
and the sanding sheet, and also helps to prevent
premature wear.
f When the tip of the sanding sheet becomes worn,
detach the sheet from the platen, rotate and reapply.
Adapter (BDCMTOA)
An accessory adapter kit is provided with BDCMTOA.
The adapter is compatible with many manufacturers'
accessories, but if unsure, confirm with the specific
manufacturer that their accessory is compatible.
Caution! To avoid injury, do not use any accessory
for an application where the adaptor may fail to hold the
accessory.
Caution! Read and follow all manufacturers' safety
warnings for any accessories used with this tool.
Caution! To avoid injury, ensure adapter and accessory
are securely tightened.
ENGLISH • 23