Intended Use - Black+Decker BDCMTO Manual De Instrucciones

22 • ENGLISH
3. No eating, drinking or smoking should be done in
the work area to prevent ingesting contaminated paint
particles. Workers should wash and clean up before
eating, drinking or smoking. Articles of food, drink,
or smoking should not be left in the work area where
dust would settle on them.
Environmental safety
1. Paint should be removed in such a manner as to
minimize the amount of dust generated.
2. Areas where paint removal is occurring should be
sealed with plastic sheeting of 4 mils thickness.
3. Sanding should be done in a manner to reduce
tracking of paint dust outside the work area.
Cleaning and Disposal
1. All surfaces in the work area should be vacuumed
and thoroughly cleaned daily for the duration of the
sanding project. Vacuum filter bags should be
changed frequently.
2. Plastic drop cloths should be gathered up and
disposed of along with any dust chips or other
removal debris. They should be placed in sealed
refuse receptacles and disposed of through regular
trash pick-up procedures. During clean up, children
and pregnant women should be kept away from the
immediate work area.
3. All toys, washable furniture and utensils used by
children should be washed thoroughly before being
used again.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The following table
shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier
the cord.
Voltage
Total length of cord in meters (m)
(Volts)
120-127V 0-7
220V 0-15
Rated
Minimal cross-sectional area of the
Ampere
Range
0-6A 1,0
6-10A 1,0
10-12A 1,5
12-16A 2,5
7-15 15-30
15-30 30-60
cord in milimeters (mm )
2
1,5 1,5
1,5 2,5
1,5 2,5
4,0 Not recommended

INTENDED USE

Detail Sanding
Sanding in extremely tight areas otherwise difficult to
reach and require hand sanding. Select a high oscillating
frequency. Sand with continuous motion and light
pressure. Applying excessive pressure does not increase
material removal; but will prematurely wear sanding
sheets.
Flush Cutting
Remove excess wood from door jamb, window sill and/or
toe kick. Removing excess copper or PVC pipe.
Removal Work
Carpets & backing, old tile adhesives, caulking on
masonry, wood and other surfaces.
Removal of Excess Materials
Tile grout, plaster, mortar splatters, concrete on tiles, sills.
Preparation of Surfaces
New floors and tiles.
OPERATING INSTRUCTIONS
Warnings! Shock hazard. Under no circumstances
should this product be used near water.
Warnings! Risk of lacerations or burns. Do not touch
work piece or accessory immediately after operating the
tool. They can become very hot. Handle carefully. Always
allow accessories and work piece to cool before handling.
Warnings! To reduce the risk of injury, turn off and
remove battery from tool or disconnect plug from power
source before making any adjustments or removing
or installing attachments or accessories. Remove any
accessory from the attachment before removing or
installing the attachment.
Note: Refer to Power Unit instruction manual before
operating this tool for all safety warnings and details on
installing and removing attachments.
Operation
30-50 f To switch the tool on, press the variable speed switch
on the power unit. The tool speed depends on how far
60-100
you press the switch.
f To switch the tool off, release the variable speed switch.
Note: This attachment only operates in the forward
direction, the forward/reverse slider of the Power Unit
2,5
should not be able to be switched to reverse.
4,0
Installing/removing accessories
4,0
This tool features a tool-free accessory changing system.
This allows for faster accessory changes without the need
for wrenches or hex keys like other oscillating tool systems.