Cequent Fulton Instrucciones

Read, Understand, Follow and Save These Instructions
Read, understand and follow all of these instructions and warnings (Instructions) before installing and using this product. Install and use this product only
as specified in these instructions. Improper installation or use of this product may result in property damage, serious injury, and/or death. Never allow
installation or use of this product by anyone without providing them with these instructions. You must read, understand and follow all instructions and
warnings for any product(s) to which this product is used in conjunction with or installed. Save these instructions with the product for use as a reference
for any future installation and use of the product.
WARNING
• Purchaser/owner must ensure that product is
installed according these instructions. Purchas-
er/owner must not alter or modify product.
• Operator and bystanders should never position
any part of body under any portion of this prod-
uct or the load being supported.
• Do not allow children to play on or around this
product or the load being supported.
• Do not use winch to move humans.
• Never exceed maximum rated capacity. Refer
to stamped markings or decals on product to
obtain rated capacity. If uncertain, contact
Cequent Performance Products at 1-800-632-
3290 or www.cequentgroup.com
• Always inspect the cable or strap and its
attachment before each use to make sure they
are not damaged. Never use them if they are
worn, kinked, or frayed. If the cable or
attachment breaks, the cable will whip violently,
causing property damage, serious bodily injury,
and/or death.
• Never stand along side the winch cable, strap, or
rope or guide the cable, strap, or rope with your
Installation Instructions
(Mounting hardware not supplied.) The winch stand must be capable of supporting at least five times the rated capacity of the winch. The mounting
surface must be equal to or greater than the footprint of the winch frame. When attaching the winch, use 3/8" dia. grade-5 hardware and torque to 28-
30 ft-lbs. Mounting bolts will vary in length for each application. Check final installation and make sure winch is secure to mounting structure.
Handle
Drum
Drum
Bolt
Input
Shaft
Ratchet
Pawl
Handle
Locknut
Attaching a Handle:
Assemble the handle onto the flatted input shaft end. Tighten the 1/2" - 13 locknut against handle and torque to 22-25 ft-lbs. Do not over torque.
Attaching Winch Line (Rope, Strap or Cable):
Always maintain a minimum of three complete wraps of rope, strap or cable on the drum. If attaching strap without strap anchor to a XLT– series
winch, remove the drum bolt and gently separate the plastic cover to allow the winch drum to be removed. Install the strap according to the instruc-
tions below and re-install the winch drum as it was before. On XLT14 or XLT18 series winches torque the drum locknut to 9-10 ft-lbs. On XLT20,
XlT26, or XLT32 series winches torque the drum locknut to 24 ft-lbs.
frame, and keep the drum from turning.
Attaching a Rope:
Attaching a rope to the winch drum requires no bolts, nuts, or clamp. The rope must weave through the drum outer
wall and be secured beneath itself as shown in the illustration.
Attaching a Strap:
Winches designed for a strap have holes in the drums to accommodate a strap cross
bolt. A grade 5 bolt of the largest possible diameter is required for strap mounting
(see chart on following page). Tighten the locknut just to where end play in bolt is
taken up. Over-tightening can deform drum. For winches having a strap anchor in-
cluded, pass the strap loop under the cross bolt, insert strap anchor in the strap loop,
then pull tight.
Attaching a Steel Cable to a Drum:
Pass the cable from the inside of the drum through one of the dimpled holes in the outer plate. Loop the
cable around the drum bearing, under itself, and leave 1" of cable extending past the clamp location.
Tighten the clamp nuts to approximately 2 ft-lbs.
1) Inspect rope, strap or cable and replace if damaged.
2) Check mounting hardware for proper tightness and tighten if necessary.
3) Apply a drop or two of #30 weight engine oil to each bushing I.D. and to the ratchet pawl pivot points. Maintain a thin layer of chassis grease on
the gear teeth.
Trailer Winches
®
Failure to follow these warnings and instructions may result in
property damage, serious bodily injury, and/or death.
hands.
•Never operate with slippery, wet, or oily hands
and always maintain a firm grip on the winch
handle. Do not attempt to stop a winch by
grabbing the handle while in motion.
• Always maintain a minimum of three (3)
complete wraps of cable or rope on the drum, or
three layers of strap on the drum.
• Only winches that have a hub diameter of 1 3/4"
can accommodate steel cable.
• Assure there is adequate safety factor, of at least
3 times the maximum load for all components
used.
• A loud clicking sound from the ratchet must be
heard when lifting the load. If a loud clicking
sound is not heard, do not use and replace
ratchet components immediately.
• Never release the crank handle unless the
ratchet pawl is fully engaged and the load is
supported.
• In no case will a one-way ratchet pawl system
hold the load when it is being let out.
• Never leave a weight supported from the winch
Brake Lever
(optional)
Prior to Use
Warning: Failure to follow these warnings and instructions may result
in property damage, serious bodily injury, and/or death.
Drum
Hub
Shift Lock
Lever
Be sure not to over tighten as this may crush the spacer between the
Strap Anchor
while the winch is unattended, as another person
may attempt to operate the winch, thereby
creating an unsafe condition.
• This winch is designed for manual operation
only and the load rating is based on an
intermittent duty cycle.
• Excessive force in turning winch handle may
indicate overload. Winches require maximum
of 45 lbs of handle force to pull their rated load.
• If you cannot crank the winch with one hand
you are potentially overloading the winch.
• On two speed winches, make sure that the
ratchet pawl is properly engaged and holding
the load before attempting to change gears.
• Winches are not designed to secure boats to
trailers while towing. Boat tie downs should
be used for this purpose.
• Periodically check mounting hardware for
proper torque and tighten if necessary.
Always replace bent, broken, or worn parts

before using this product.
This product is rated according to SAE J1853

Ratchet
Pawl
Strap
Outer
Plate
Drum
Bearing
F3295 (Rev-F 16437) 12/11
Handle
Input
Shaft
Handle
Locknut
Rope
Cable
Keeper
Cable