Ecoflam MAX GAS 40 P Manual De Instrucciones página 9

Function
- SIEMENS LME11... control and safety unit
Connection diagram and control sequence of LME11...
K1
K2/1 K2/2
R / W
T
GP
AL
M
STB
H
Si
N
AGK25... PTC resistor
AL Error message (alarm)
V... Fuel valve
CPI Closed Position Indicator
DBR... Wire link
EK Lockout reset button (internal)
EK2 Remote lockout reset button
ION Ionization probe
FS Flame signal
FSV Flame signal amplifier
GP Pressure switch
H Main switch
HS Auxiliary contactor, relay
K1...4 Internal relays
KL Low-fire
LK Air damper
Status
Waiting time «tw», other waiting states
Ignition phase, ignition controlled
Operation, flame o.k.
Operation, flame not o.k.
Extraneous light on burner startup
Undervoltage
Fault, alarm
Error code output (refer to «Error code
table»)
Interface diagnostics
Legend: ....... Steady on
Red blink code of
signal lamp (LED))
2 blinks
3 blinks
4 blinks
5 blinks
6 blinks
7 blinks
8 blinks
9 blinks
10 blinks
14 blinks
420010266506
RESET
K3
p
Z
V1
7101a24e/0609
LKP Air damper position
LP Air pressure switch
LR Load controller
M Fan motor
R Control thermostat /
pressurestat
STB Safety limit thermostat
Si External pre-fuse
t Time
W Limit thermostat / pressure
switch
Z Ignition transformer
ZV Pilot gas valve
A Start command (switching on
by «R»)
B-B´ Interval for establishment of
Color code table for multicolor signal lamp (LED)
Color code
❍ ...................................................................................
● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍
❑...................................................................................
❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍
❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲
● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲
▲...................................................................................
▲ ❍ ▲ ❍
▲ ▲ ▲
▲ ❑
Red
Error code table
«AL» at Possible cause
term. 10
on No establishment of flame at the end of «TSA»
- Faulty or soiled fuel valves - Faulty or soiled flame detector
- Poor adjustment of burner, no fuel - Faulty ignition equipment
on «LP» faulty
- Loss of air pressure signal after «t10», - «LP» welded in normal position
on Extraneous light when burner is started up
on Time out «LP»
- «LP» welded in working position
on Free
on Too many losses of flame during operation
(limitation of the number of repetitions)- Faulty or soiled fuel valves.
- Faulty or soiled flame detector - Poor adjustment of burner.
on Free
on Free
off Wiring error or internal error, output contacts, other faults.
on CPI contact not closed
A
SB / R
W / GP
AL
M
Z
V1
LP
FS
EK2
EK2
tw t10
▲ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲ ❍
▲ ▲ ▲ ▲ ▲ ▲ ▲
❍
Green Off
B B´ C
t1 t4
t3 t3n
TSA
flame
C Operating position of burner
reached
C-D Burner operation (generation
of heat)
D Controlled shutdown by «R»
t1 Prepurge time
t3 Preignition time
t3n Postignition time
t4 Interval between ignition
«Off» and release of «V2»
t10 Specified time for air pressure
signal
TSA Ignition safety time
tw Waiting time
Color
Off
Flashing yellow
Green
Flashing green
Green-red
Yellow-red
Red
▲ ❍
Flashing red
▲ ▲
Red flicker light
●
Yellow
www.ecoflam-burners.com
EN
D
9