Tabla de contenido
Idiomas disponibles
Idiomas disponibles
NOTE: Before starting installation, read all the steps of
these instructions.
Use the illustration beside to identify your kitchen cabinet
type.
This manual covers 2 kinds of installation: the standard
(without EZ1 brackets) and the EZ1 one-person installation
system (using included template and brackets). For the
standard installation, go to page 14.
EZ1 installation is designed for use with kitchen cabinets that have the same width designation as the range hood width.
If the cabinet is greater than 1/2" wider than the range hood width, please use the standard installation method.
1. Use the proper template for vertical OR horizontal
disharge (included) for placement of ductwork and
electrical cutout in cabinet or wall. For a non-ducted
installation, DO NOT cut a duct access hole, only cut the
hole for electrical wiring. If replacing a hood and plan to
use the existing duct and electrical, steps 2 to 5 may not
be necessary. If so, skip to step 6.
2. Measure and mark the hood center line on cabinet bottom.
4. Drill a 1/8" dia. pilot hole for house wiring, at B location
on template.
5. Use a sharp pencil or 1/8" drill bit to mark the locations
for the appropriate duct access holes (16 locations for 7"
round duct, or 4 corner locations for rectangular duct).
Remove the template.
PREPARE THE HOOD LOCATION
EZ1 One-person installation system
CABINET FRONT
Use this template for marking; do not attempt to cut out the ducting hole through it.
M
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
ARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
FOR THE APPROPRIATE SIZE DUCT OPENING
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
7" R
OUND
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
M
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C
Bend template along graduated
C
scale when installing to framed
ONDUIT ROND DE
cabinet.
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
l'armoire et plier le gabarit en
T
8"
ITLE TO BE TRANSLATED IN
conséquence.
C L
To be translated in Spanish.
C
ONDUCTO REDONDO
7
DE
7½"
V RTICAL EX
VERTICAL EXHAUST
A
A
A
10½"
14½"
C
Place this edge against back wall
Appuyer ce bord au mur arrière
Apoyar este borde contra la pared de atrás
C
F
OLD TEMPLATE ALONG GRADUATED
SCALE WHEN INSTALLING TO FRAMED
P
.
CABINET
CENTER LINE
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
HORIZONTAL EXHAUST
FRAMED CABINET
3. Align the center line on template with the hood center
line marked on the bottom of the cabinet, placing the
edge (where indicated) of the template against back
wall. When using with framed cabinet for vertical exhaust
installation, fold over rear edge of template equal to the
depth of the cabinet frame at the wall (use graduations
on template, C locations on template). Tape the template
in place.
NOTE: When facing the installation, A and B (on
template) must be at right.
OR
D
UCTING
R
ECTANGULAR
D
UCTING
= 3¼" x 10"
= 3¼" x 14"
7
OU
C
PO
ONDUIT RECTANGULAIRE
= 3¼ po x 10 po
= 3¼ po x 14 po
S
PANISH
O
C
ONDUCTO RECTANGULAR
.
= 3¼ pulg. x 10 pulg.
PULG
= 3¼ pulg. x 14 pulg.
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
S
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
4¼"
A = single blower hood
B = double blower hood
A
B
C
CENTER LINE
HORIZONTAL
EXHAUST DUCTING
A
B
Place this edge against
cabinet bottom.
Appuyer ce bord contre le bas
Electrical access hole center
de l'armoire.
A = single blower hood
B = double blower hood
Apoyar este borde contra
la base del armario.
Centre du trou pour fil
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
C L
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
M
M
ARK WHERE INDICATED
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
FOR THE APPROPRIATE SIZE DUCT OPENING
LE FORMAT DE CONDUIT UTILISÉ
R
ECTANGULAR
D
UCTING
C
ONDUIT RECTANGULAIRE
= 3¼" x 10"
= 3¼ po x 10 po
= 3¼" x 14"
= 3¼ po x 14 po
T
ITLE TO BE TRANSLATED IN
S
PANISH
C
ONDUCTO RECTANGULAR
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
T T
ELECTRICAL
ACCESS HOLE
LOCATION (B)
6. Draw the border for the exhaust ducting by linking its
marks (16 for round duct and 4 for rectangular duct), then
cut the opening in the cabinet bottom (vertical exhaust)
or in the wall (horizontal exhaust). Drill the house wiring
hole by using a 1½" hole saw centered with the pilot hole
previously made in 4.
10
FRAMELESS CABINET
VERTICAL
EXHAUST DUCTING
CABINET FRONT
Use this template for marking; do not attempt to cut out the ducting hole through it.
M
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
ARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
FOR THE APPROPRIATE SIZE DUCT OPENING
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
7" R
OUND
D
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
M
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C
Bend template along graduated
C
scale when installing to framed
ONDUIT ROND DE
cabinet.
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
l'armoire et plier le gabarit en
T
8"
ITLE TO BE TRANSLATED IN
conséquence.
C L
To be translated in Spanish.
C
ONDUCTO REDONDO
7
DE
PULG
7½"
V RTICAL EX
VERTICAL EXHAUST
A
A
A
10½"
14½"
C
ELECTRICAL
ACCESS HOLE
LOCATION (B)
(
IN CABINET BOTTOM
B
ess hole center
wer hood
wer hood
(
)
IN WALL
OR
UCTING
R
ECTANGULAR
D
UCTING
= 3¼" x 10"
= 3¼" x 14"
7
OU
C
PO
ONDUIT RECTANGULAIRE
= 3¼ po x 10 po
= 3¼ po x 14 po
S
PANISH
O
C
ONDUCTO RECTANGULAR
.
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
S
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
4¼"
A = single blower hood
B = double blower hood
A
B
C
B
)
Capítulos
Tabla de contenido
