Battery Charger Safety; Product Familiarisation; Intended Use; Unpacking Your Tool - GMC GMCSDS18 Manual Del Usuario

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 44
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow these
instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20˚C)
• Ensure battery contacts cannot accidentally short in storage. Keep batteries clean; foreign
objects or dirt may cause a short. Keep away from other metal objects, for example,
paperclips, coins, keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause
skin irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help
• DO NOT open, disassemble, crush, heat above 60°C, or incinerate. Do not dispose of in
fire or similar
GB

Battery Charger Safety

Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger before attempting
to charge the battery.
• Do not attempt to use the charger with any batteries other than those supplied. Keep your
battery charger clean; foreign objects or dirt may cause a short or block air vents. Failure
to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard
• Examine the battery charger regularly for damage, especially the cord, plug and enclosure.
If the battery charger is damaged, it must not be used until it has been repaired
• Children should be supervised to ensure that they do not play with the appliance
WARNING: DO NOT attempt to recharge non-rechargeable batteries.
Battery and charger safety features
The battery and charger are fitted with a number of safety features which may be triggered
during charging or operation:
• Over-charge protection: Charger automatically switches off when the battery has
reached full charge capacity, protecting the internal components of the battery
• Over-discharge protection: Prevents the battery from discharging beyond the
recommended lowest safety voltage
• Over-heat protection: Sensor switches off if the battery becomes too hot during
operation. This can happen if the tool is overloaded or being used for extended periods
of time. Up to 30 minutes cooling time may be required depending on the ambient
temperature
• Overload protection: Battery temporarily stops if it is overloaded or the maximum current
draw is exceeded, protecting the internal components. The battery will resume normal
operation when the current draw returns to a normal safe level. This may take a few
seconds
• Short circuit protection: The battery will stop working immediately if a short circuit
occurs, this prevents damage to the battery or tool

Product Familiarisation

1. Auxiliary Handle
2. Mode Selector
3. Mode Selector Release
4. Gear Switch
5. Motor Vents
6. Insulated Handle
7. Forward/Reverse Switch
8. Trigger
9. Battery Charge Indicator
10. Battery Slot
11. Battery
12. Battery Release
13. Auxiliary Handle Mounting
14. Chuck Collar
15. Chuck
16. Depth Stop
17. Red LED
18. Battery Charger
19. Green LED
Accessories (not shown)
• 6pce drill bit accessory kit
• Carry bag
Note: This manual may be supplied with different package configurations including bare tools
and supplied accessories may vary

Intended Use

Portable light-duty battery-powered drill optimally designed for drilling masonry. Also capable
of drilling wood and metal with the optional purchase of a standard chuck with SDS Plus
connector.

Unpacking Your Tool

• Carefully unpack and inspect your new sander. Familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool

Before Use

Removing a battery
• To remove the Battery (11) from the tool, press the Battery Release (12), then slide the
Battery out of the Battery Slot (10)
WARNING: DO NOT try to remove the Battery without pressing the Battery Release button.
The tool or Battery could be damaged.
Fitting a battery
1. To fit a charged battery, slide it on to the Battery Slot (10) of the tool until it clicks and locks
into position
Note: Make sure the Battery and tool are lined up correctly. If the Battery does not slide into
the tool easily, don't force it. Instead, slide the Battery out of the tool again, check the top of
Battery and the tool battery slot are clean and undamaged and that the contacts are not bent.
Setting up the battery charger
1. If fitted, remove any battery from the Battery Charger (18)
2. Insert the Battery Charger mains plug into a suitable mains socket
Note: The Green LED (19) on the Battery Charger will flash to indicate that the charger is
ready to charge the battery.
WARNING: Use this charger ONLY to charge the supplied battery or additional purchased
batteries that are specifically designed for this tool.
WARNING: The charger is designed for indoor use only, and MUST NOT be used in damp
or wet conditions.
8
Tabla de contenido

Solución de problemas

loading

Tabla de contenido