Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Connection scheme for the use of three sensors on five control units
Control unit 1
WIND
SENSOR
13. Guide to the resolution of the problems
PROBLEMS
1)
At the instant of the switching on of the
control unit all the led (red, yellow,
green) do not switch on for 1 second
2)
The keys of the transmitter do not have
any effect on the control unit
3)
The red led keep on blinking
4)
The sunshade does not automatically
open
5)
The sunshade does not automatically
close
6)
After an alarm of wind or rain the
sunshade does not reopen itself
GUARANTEE - In compliance with legislation, the manufacturer's guarantee is valid from the date stamped on the product and is restricted to the repair or
free replacement of the parts accepted by the manufacturer as being defective due to poor quality materials or manufacturing defects. The guarantee does
not cover damage or defects caused by external agents, faulty maintenance, overloading, natural wear and tear, choice of incorrect product, assembly
errors, or any other cause not imputable to the manufacturer. Products that have been misused will not be guaranteed or repaired. Printed specifications
are only indicative. The manufacturer does not accept any responsibility for range reductions or malfunctions caused by environmental interference. The
manufacturer's responsibility for damage caused to persons resulting from accidents of any nature caused by our defective products, are only those
responsibilities that come under Italian law.
6-1621095
rev.9
19-07-2012
RAIN
SENSOR
LIGHT
SENSOR
•
Power supply absent
•
The plug is not inserted
•
The connection to the electric net is absent
•
The safety device has intervened
•
Control unit not working
•
The transmitter has not been learned by the control
unit
•
The transmitter is not compatible with the control unit
•
Battery of the transmitter not working
•
Rain alarm active (wet)
•
Rain sensor is breakdown
•
Wind alarm active
•
Wind sensor breakdown
•
Slow external luminosity (green led turned off or with
slow blinking)
•
Motor of the sunshade not working (green led turned
off)
•
Control unit not functioning
•
Elevated external luminosity (green led with quick
blinking)
•
Control unit not functioning (green led turned off)
•
Control unit not working
•
Red led blinking
•
Dip – switch 1 on OFF position
•
The last movement made by the sunshade has been
a movement of closing
•
The intensity of the light detected by the sensor is
less than the minimum threshold (threshold of
closing) (green led turned off)
•
Motor of the sunshade not working
•
Control unit not working
ITA
Control unit 2
CAUSE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ENG
FRA
ESP
DEU
POR
Control unit 5
SOLUTIONS
Wait that it is reset
Insert the plug
Check the connections (page 1 )
Check the connections and reset the device
Execute the learning of the transmitter (section 6)
Verify if the transmitter belongs to CLARUS or BIROL
series 433 MHz
Replace the battery of the transmitter
Verify points 1 and 2
Wait that the atmospheric conditions get better and the 7
minutes for the automatic reset
Check the correct installation of the sensor
Check the wiring of the sensor (page 2)
Contact the technician installer to raise the wind alarm
threshold (section 8.2.1).
Open manually the sunshade
Check the correct installation of the luminosity sensor
and the threshold of automatic opening
Verify points 1,2,3,4
Close manually the sunshade (section 8.1)
Check the correct installation of the sensor of luminosity
(for example far away from luminous sources, luminous
signs, etc.)
Contact the technician installer
Verify points 1,2,3,4
Contact the technician installer
Wait for 7 minutes from the last recording of the alarm
Put the dip – switch 1 on position ON
The last order must be of opening
16 / 32
Tabla de contenido
