Switching On/Off; Intercom Mode - Caberg Just Speak Sintesi Manual De Seguridad E Instrucciones

EN
-
+
tones or ringing tone for an incoming call. Press the multifunction button or to accept the call (short press).
How to pair a Bluetooth® MP3 player to the CABERG JUST SPEAK system
The player/helmet pairing procedure is managed through the player.
The helmet is seen by the MP3 reader (or by a phone fitted with A2DP) as a Bluetooth® head-set. Refer to your Bluetooth® player user manual, under
"Pairing Bluetooth® devices", to check the pairing procedure which varies from player to player.
Pair the helmet after you have mastered your player's pairing procedure.
Start with the helmet off.
-
Enter pairing mode by keeping multifunctional button on the helmet for 10 seconds until the LED starts to flash quickly and the helmet emits an
acute tone, showing the pairing acceptance stage (NOTE: the LED comes on and the helmet emits a tone after 4 seconds, continue to keep the button
pressed until you hear the acute tone and the LED starts flashing quickly).
Proceed rapidly (40 seconds) with the pairing, using the player, with the Bluetooth® device pairing procedure appropriate for each MP3 player.
The name Caberg BTKit (or the name chosen during configuration) will appear on the player's display in the list of devices.
Select Caberg BTKit (or the name you choose during configuration).
When asked for the password, enter 0000.
The helmet will confirm successful pairing by a tone in the head-set and the LED will start flashing slowly.
Switch both the player and the helmet off and then on to store the pairing data.
The pairing is stored by the helmet and is not lost at switch-off.
If the pairing has not been successful, switch off the helmet (see how to switch off the helmet) and repeat the pairing procedure from the beginning.
+
NOTE: some MP3 players, after having been paired, must be connected to the helmet by pressing button and releasing it immediately. This brief
+
connection procedure must be repeated each time the helmet is switched on (switch on the helmet and then press and release button).
Check your player's operating mode and any special operating options relative to the use of Bluetooth®.
Once the helmet is connected to the Bluetooth® device it is possible to listen to music using the player's play button.
After pairing (see above), all you need to do to use the helmets is follow the switching on/off procedures.
NOTE: Read the "Intercom mode" and "Handset mode" paragraphs below before switching the helmets on.
How to switch the helmet on and off
-
Switching on: Press button until you ear a tone in the earpiece. Release the button. The LED starts flashing slowly: the helmet is now on.
-
Switching off: Press the multifunction button until you ear the closing melody in the earpiece.
Release the button. The LED goes off.
NOTE: If the system fails to respond to the multifunction button commands, charge the battery for a few minutes (5-10 minutes). The device then resets.
If the battery is completely flat, just a few minutes charging are still enough to check that the system is working correctly.

Intercom mode

First switch on the Slave helmet, wait about 20 seconds, and then the Master.
As soon as it has been switched on, the Master searches for the Slave and connects to this automatically: the helmets are now ready to communicate.
The helmets are also ready to accept any incoming calls.
-
If the two helmets fail to connect (low-pitched tone) simply press button (medium press), otherwise switch them off and start again.
-
Two paired helmets that have been switched on can be connected or disconnected at any time by pressing button on the Master or Slave helmet
(medium press).
The helmets can be in Intercom and connected to their respective mobile phones, but there could be some limitations with certain phones that have
A2DP (that manages the sending of music via Bluetooth®) that might not permit simultaneous use of the Intercom.
The Intercom function also has special functions for pairing several helmets at the same time and how the system behaves if the signal is lost. These
functions can be configured exclusively through the configuration software included. Please see the "Configurator mode" paragraph for further details.
24