English - Kenwood FP270 Serie Manual Del Usuario

before using your Kenwood appliance
Read these instructions carefully and retain for future reference.
G
Remove all packaging and any labels.
G
safety
G The blades and discs are very sharp, handle with care. Always
hold the knife blade by the finger grip at the top,
away from the cutting edge, both when handling and
cleaning.
Always remove the knife blade before pouring contents from the
G
bowl.
Keep hands and utensils out of the processor bowl and liquidiser
G
goblet whilst connected to the power supply.
Switch off and unplug:-
G
before fitting or removing parts;
G G
when not in use;
G G
before cleaning.
G G
Never use your fingers to push food down the feed tube. Always
G
use the pusher/s supplied.
Before removing the lid from the bowl or liquidiser/mill from the
G
power unit:-
switch off;
G G
wait until the attachment/blades have completely stopped;
G G
be careful not to unscrew the liquidiser goblet or mill jar from
G G
the blade assembly.
Liquids should be allowed to cool to room temperature before
G
blending.
Do not use the lid to operate the processor, always use the on/off
G
speed control.
This machine will be damaged and may cause injury
G
if the interlock mechanism is subjected to excessive
force.
Never use an unauthorised attachment.
G
Never leave the appliance unattended when it is operating.
G
Never use a damaged appliance. Get it checked or repaired: see
G
'service & customer care'.
Never let the power unit, cord or plug get wet.
G
Don't let excess cord hang over the edge of a table or worktop
G
or touch hot surfaces.
Do not exceed the maximum capacities stated in the
G
recommended speed chart.
This appliance is not intended for use by persons (including
G
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play
G
with the appliance.
Only use the appliance for its intended domestic use. Kenwood
G
will not accept any liability if the appliance is subject to improper
use, or failure to comply with these instructions.
Misuse of your processor/liquidiser can result in injury.
G
Refer to the relevant section under "using the attachments" for
additional safety warnings for each individual attachment.
before plugging in
Make sure your electricity supply is the same as the one shown
G
on the underside of your machine.
This appliance conforms to EC directive 2004/108/EC on
G
Electromagnetic Compatibility and EC regulation no. 1935/2004
of 27/10/2004 on materials intended for contact with food.
before using for the first time
1 Remove all packaging including the plastic blade covers from the
knife blade. Take care the blades are very sharp. These
covers should be discarded as they are to protect the blade
during manufacture and transit only.
2 Wash the parts see 'cleaning'
3 Push excess cord into the back of the machine.
key
processor
pusher
feed tube
lid
bowl
detachable drive shaft
speed + pulse control
power unit
safety interlock
cord storage
glass liquidiser
blade unit
sealing ring
goblet
lid
filler cap
glass mill
blade unit
sealing ring
jar
attachments
knife blade
dough tool
twin beater geared whisk
thick slicing/coarse shredding disc
thin slicing/fine shredding disc
rasping disc
geared citrus press
centrifugal juicer
spatula
to use your food processor
1 Fit the detachable shaft onto the power unit
2 Then fit the bowl. Place the handle towards the back and turn
clockwise until it locks
3 Fit an attachment over the drive shaft.
Always fit the bowl and attachment onto the machine before
G
adding ingredients.
4 Fit the lid - ensuring the top of the drive shaft locates into the
centre of the lid.
Do not use the lid to operate the processor, always
G
use the on/off speed control.
5 Switch on and select a speed.
Your processor will not operate if the bowl or lid are
G
not fitted correctly into the interlock. Check that the
feed tube and bowl handle are situated to the right
2
.
.