Sammic SGA Instrucciones De Uso página 6

CE Marking Indications
Each appliance is identified
following data:
· Manufacturer's name
SAMMIC S.A. c/ Atxubiaga 14 Azpeitia
Gipuzkoa (SPAIN).
· "CE" mark.
· The machine model as stated in the next
section.
· The serial number as indicated on the
guarantee slip and the Declaration of
Conformity.
MODELS
This manual describes the installation,
operation and maintenance of the V-
402SGA, V-421SGA, V-426SGA, V-641SGA,
V-821SGA, V-821LLSGA
machines (percentage vacuum sensor
controlled version).
The model reference and its specifications
are shown on the nameplate affixed to the
machine.
These vacuum packaging machines have
been designed and manufactured in
accordance with the following European
directives: 89/392/EEC,
73/23/EEC.
INSTALLATION
For optimum performance and long service
life of the machine, follow the instructions
contained in this manual rigorously.
Location
Place the machine so that it stands
perfectly levelled. To avoid damages, never
lean the machine on one of its sides.
Electric connection
1.M
OTOR SPECIFICATIONS
-Single-phase motors are supplied for
feeding at 230V.
-Three-phase motors are suitable for 230V
or 400V (connection to 400V).
Before connecting the vacuum packaging
machine to the mains, check if the motor is
prepared for the same voltage as the
mains. Otherwise, change the voltage.
To change the voltage:
1.Connect the transformers to the suitable
voltage, as shown in the terminal strip.
2. If necessary, change
6
ENGLISH
connections as shown in the terminal
box.
by the 3. If necessary, adjust the temperature
relay as shown on the electric diagram.
and address:
2.- C
ABLE SPECIFICATIONS
The SAMMIC vacuum packaging machines
are supplied with one thermoplastic-
sheathed cable 1.5m in length.
THEY MUST BE EARTHED. The grounding
wire of the machine is identified.
-Three-phase machines: Prepare one 20A,
3PN+T wall socket and connect a sealed
plug to power cord of the vacuum
packaging machine.
-Single-phase machines: Prepare one 20A,
2P+T wall socket and the corresponding
plug.
packaging
3.-T
O CHANGE
(three-phase machines only):
If the vacuum pump motor generates
unusual noise on starting the machine, this
means that the motor rotates in the wrong
direction. In this event, immediately stop
the machine and invert two feed wires.
STARTING
93/68/EEC,
Whatever the machine model, the pump
contains oil. After pressing the general
switch, it is necessary to perform a few
cycles on no load before proceeding with
the first packing, so that the oil can heat up
and provide the right vacuum.
Sensor controlled vacuum %
This concerns the models in which all the
functions (programming, vacuum, gasflush
and sealing) are microprocessor-controlled.
An extremely
digitally actuated sensor, enabling a
vacuum of up to 99.5% to be produced in a
reliable and safe manner, also offers the
possibility of creating an additional time-
controlled vacuum.
M
AIN FEATURES
-Fast and simple programming.
-Storage of 10 programmes.
-Automatic counter of the machine running
hours, with oil change warning signal.
-Automatic storage of the last executed
programme.
-Storage
disposable cell.
the motor -LED-display of every stage executed within
THE DIRECTION OF ROTATION
accurate (within 0.2%)
of programmes without
the cycle.
-STOP key for stopping any phase of the
cycle and going over to the next one.
Technical description of the control panel
Display 1
When the operator switches on the main
switch of the machine, the display shows,
for two seconds, the number identifying
the machine configuration. Besides, it
serves to indicate the number of the
selected programme (from 0 to 9).
Display 2
When the operator switches on the main
switch of the machine, the display shows,
for two seconds, the number, which
multiplied by ten gives the accumulated
working hours of the vacuum pump. For
example, the display of figure 10 at any
one time would mean that the accumulated
working time is 100 hours. Afterwards, the
vacuum, gas, sealing time and other values
can be displayed by pressing the respective
key. On turning on the machine when the
pump has been working for a total of 500
hours, the indicator will display 50 and will
be flashing for 10 seconds, indicating that
oil must be changed. During this lapse of
time, the machine will not start, even if the
cover is lowered.
+Key
Incrementer
It serves to increase any of the values
shown in either display. Keep the key
depressed to reach the required value
faster.
-Key
Decrementer
It serves to decrease any of the values
shown in either display. Keep the key
a depressed to reach the required value
faster.