Filling The Water Tank; Vertical Steam Ironing; Dry Ironing - TEFAL AQUASPEED AutoClean Manual Del Usuario

1800117476 FTG AutoClean E0:125x210
Preparation
What water to use ?
• Your appliance has been designed to operate using untreated tap water.
However, it is necessary to operate the Self-Clean function regularly in order
to eliminate hard water deposits from the steam chamber.
• Heat concentrates the elements contained in water during evaporation. The
types of water listed below contain organic waste or mineral elements that
can cause spitting, brown staining, or premature wear of the appliance:
water from clothes dryers, scented or softened water, water from
refrigerators, batteries or air conditioners, pure distilled or demineralised
water or rain water should not be used in your Tefal iron.
Fill the tank up to the
"MAX".
Never fill the appliance
by holding it directly
under the tap.
Use
Adjust the temperature and the steam
• Set the thermostat control – fig.4, referring to the table below.
• The thermostat light comes on. It will go out when the soleplate is hot enough – fig.5.
RECOMMENDATIONS
FABRIC
LINEN
COTTON
WOOL
SILK
SYNTHETIC
(Polyester,
Acetate, Acrylic, Nylon)
• Your iron heats up quickly: so begin by ironing fabrics that are ironed at low tempe-
ratures first, then go on to those requiring a higher temperature,
• If you turn down the thermostat, wait until the thermostat light comes
back on before beginning to iron again,
• When ironing fabrics with mixed fibres, set the ironing temperature for the
most delicate fibre. For delicate fabrics we recommend testing the fabric
first on an inconspicious place eg (inside the hem).
Make sure that there is
water in the tank before
using this button.
Obtain more steam
• Press the Turbo button
• Wait a few seconds between each shot before pressing the Turbo button again.
Hold the iron a few
centimetres from the
fabric to avoid burning
delicate fabrics.

Dry ironing

• Set the temperature for the fabric to be ironed.
• Set the steam control to "0" – fig.1.
• You may start ironing when the thermostat light goes out.
• Check that the Ultracord system is properly locked.
• Unplug your iron before filling it.
• Set the steam control to "0" – fig.1.
• Take the iron with one hand and tilt it slightly, with the nose of the soleplate
pointing down.
• To open the flap of the water tank, push the button – fig.2.
• Fill the tank up to the "MAX" line – fig.3.
• Close the flap of the water tank, until it clicks into place.
POSITION OF
THERMOSTAT CURSOR
MAX
•••
••
•
• Whether steam or dry ironing, you are able to use the spray button to dampen
laundry to remove stubborn creases –
from time to time – fig.7.
• Hang the garment on a hanger and hold the fabric slightly taut with one hand.
The steam is very hot, so you should always do this with the garment on a
hanger – never iron clothes which someone is wearing.
• Set the thermostat control to
• Press the Turbo button
bottom – fig.9, wait a couple of seconds between each use of the button.
3
29/10/09 10:33 Page 3
If your water is very hard, it is
possible to mix tap water with
store-bought distilled or
demineralised water in the
following proportions :
- 50% tap water,
- 50% distilled or
demineralised water.

Filling the water tank

STEAM SETTING
In order to avoid water dripping from
the iron onto the linen:
- Turn off the steam when ironing silk
or synthetic fabrics.
- Set it at the minimum position for
wool.
Spray Function
fig.6.

Vertical steam ironing

"MAX" – fig.8.
repeatedly – fig.7 moving the iron from top to
GB
POSITION
0
= STEAM ZONE
(spray)