Preamp Out - Evh 5150 III Instrucciones De Funcionamento

when assigning amp channel 1 to a Program Change message
for the very first time, the three amp channel LEDs will not all
illuminate briefly because the amp channel assignment has not
changed from the default amp channel 1 assignment).
If the Program Change message is currently assigned to amp
channel 1 (default), you will have to press channel SELECT {E}
twice to select amp channel 2. If the Program Change message
is currently assigned to amp channel 2, you will have to press
channel SELECT {E} twice to select amp channel 1.
4. Repeat steps 2–3 for each channel on the amp, if desired. You
can also assign multiple Program Change messages to the
same amp channel for more flexibility.
You can use the Footswitch to temporarily change channels at
any time during MIDI set up and it will have no effect on saving
the amp channel assignments. All channel assignment changes
must be made using the front panel channel SELECT buttons {E
and I}.
5. Once you are done setting up MIDI Program Changes, press
both channel SELECT buttons {E and I} simultaneously to exit
"Learning Mode." The amp is now set up to switch to the target
channels whenever the selected Program Change messages are
sent on the selected MIDI channel.
The default MIDI channel for the amp is channel 1. You can
change the MIDI channel for the amp by sending a Program
Change message from any other desired MIDI channel during
Learning Mode. The amp will then only respond to Program
Change messages and Control Change messages on that new
MIDI channel.
To use MIDI for effects loop bypass:
1. No set up is required. From MIDI channel 1 (default) or the
channel that was used to send Program Change messages in
the section above (if different from MIDI channel 1), simply
send a Control Change #85 message with a value of 63 or less to
bypass the effects loop or a value of 64 or more to enable the
effects loop.
Type: PR 1045
Part Numbers: 2253000x00* (120V, 60Hz);
2253004x00* (230V, 50Hz) UK;
2253007x00* (100V, 50Hz) JPN;
Power Requirement: 400W
Input Impedance: >1MΩ
Fuses: 100V units, F4A L, 250V;
Footswitch (included): 4-button, one / two / three / effects on-off (P/N 0091166000)
Tube Complement: Two 6L6GC output tubes, Seven 12AX7 preamp tubes
Weight: 35 lb (15.9 kg) Height: 8.5" (21.6 cm)
Recommended Speaker Enclosures: EVH 412ST (P/N 2252100x00*)
*Exterior color code: Black "x"=0, Ivory "x"=4
R.
S.
T.
U.
V.
W. SPEAKER OUTPUTS—For connection to speaker cabinet(s).
Specifications Specifications
2253001x00* (110V, 60Hz) TW;
2253005x00* (220V, 50Hz) ARG;
2253009x00* (220V, 60Hz) ROK
Power Output: 50 Watts RMS into 4, 8, or 16 Ohms
Output Impedance: 4Ω / 8Ω / 16Ω (selectable)
120V units, F4A L, 250V;
Width: 20.0" (50.8 cm)
EVH 212ST, (P/N 0082027x00*)
FOOTSWITCH—Connect the cable of the supplied footswitch
here. The footswitch allows easy selection of any of the three
channels as well as the effects loop. When illuminated, the
Green, Blue, and Red channel LEDs correspond with the chan-
nel LEDs on the amplifier's front panel.
ONE TWO
EFFECTS LOOP—Connect SEND to effects input and RETURN
to effects output.
PREAMP OUT—Connect to another amp's EFFECTS RETURN or
POWER AMP IN for simultaneous multiple amp use. This output
can also be used to send the preamp signal directly to a mixer.
RESONANCE—Adjusts the low frequency response of the
power amplifier.
LOAD IMPEDANCE—Selects the output impedance of the
amp (4, 8 or 16 Ohms) to match the speaker load.
NOTE: The 5150-III 212 speaker enclosure (recommended) has an
impedance of 16 Ohms. When using one 5150-III 212 speaker enclo-
sure, set the LOAD IMPEDANCE switch to "16Ω." When using two
5150-III 212 speaker enclosures, set the LOAD IMPEDANCE switch to
"8Ω."
When using one speaker cabinet, either jack can be used. Use
only a high-quality unshielded speaker cable, included (P/N
0073411000).
NOTE: A speaker must always be plugged into one of the speaker
jacks when the EVH amplifier is ON or damage may occur. Switch
the amplifier "OFF" or to "STANDBY" while changing speaker con-
nections or impedance settings.
Speaker Configurations are as follows:
SPEAKER SPEAKER
JACK JACK
16Ω + NONE
16Ω + 16Ω
8Ω + NONE
8Ω + 8Ω
4Ω + NONE
2253003x00* (240V, 50Hz) AUS;
2253006x00* (230V, 50Hz) EUR;
220-240V units, F2A L, 250V;
Depth: 12.0" (30.5 cm)
EVH 112ST, (P/N 0079472x00*)
THREE EFFECTS
IMPEDANCE
SETTING
= 16Ω
= 8Ω
= 8Ω
= 4Ω
= 4Ω
7 7