Chapin 10800 Guia De Inicio Rapido

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure
causing serious eye or other injury. For safe use of this product you must read and follow all
instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up
resulting in possible explosion. Do not store or leave solution in tank after use. Always wear goggles,
gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use any tool to
remove pump if there is pressure in sprayer. Never stand with face or body over top of tank when
pumping or loosening pump to prevent ejecting pump assembly and/or solution from striking
and injuring you. Never pressurize sprayer by any means other than the original pump. Do not
attempt to modify this sprayer. Replace parts only with manufacturer's original parts. Never spray
flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat, pressure,
or gas producing chemicals. Always read and follow chemical manufacturer's instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING: This product contains chemicals,
including lead, known to the state of California
to cause birth defects and other reproductive
harm. Wash hands after handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
6-8135
Dripless Shut-off
Cierre antigoteo
Arrêt anti-goutte
6-6093
Hose
Manguera
Tuyau 3-5757
Crack and Crevice Tool
Herramienta de la grieta y de la grieta
Outil de fente et de crevasse
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus) 6-4627
1. Hose to Tank
1A
2. Shut-off/Nozzle Assembly
2A
Sk-1154-1
Fan Nozzle
2B
4 Position Nozzle
2C
Loosen the retainer cap and rotate nozzle tip to align desired pattern
opening with the outlet hole in the nozzle neck. Tighten retainer cap.
Crevice Tool Attachment
1. Loosen retaining cap.
2. Align threaded hole in nozzle tip with oulet hole in nozzle neck.
3. Tighten retainer cap.
4. Screw crevice tool into threaded hole in nozzle tip to a snug fit
3-5796
4 PosistionNozzle
(Do Not Over Tighten).
Boquilla de 4 posiciones
Buse 4 positions
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
6-8096
Fan Nozzle before using. Replace with original manufacturer's parts only.
Tobera
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs
Buse
of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in
explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not
attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these
conditions are found, replace affected part with original manufacturer's part before using.
011801-4 (A) R0317
Attach the hose by screwing the swivel nut
clockwise and tightening to 37 in. lbs. Refer
to Pre-use check before using.
Brass Extension Nut
Metal Rod Brass Extension
The dripless shut-off comes assembled
as shown in figure 2A.
Metal Rod
(Not included with all models)
(for use with 4 position nozzle only)
2D
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
5. Pressurizing and Spraying
5A 5B
TO LOCK HANDLE: Push handle down to depress coil
TO LOCK PUMP: Place pump prongs down into
spring and turn handle 1/4 turn clockwise, then allow
slots in funnel, turn clamp clockwise to furthest
handle to raise into lock position.
position under bottom slot, then turn handle
clockwise until tightly locked and sealed in place.
5D
5E
TO UNLOCK PUMP: TO RELEASE HANDLE:
Push down to depress coil
Turn handle counterclock-
wise until 3-prong clamp spring and turn handle coun-
terclockwise 1/4 turn, then
is loose. Then rotate clamp
lift handle.
counterclockwise to stop
and lift out.
6. Lock Off
For safety lock-off feature (no-spraying), push trigger
forward and rotate locking mechanism into lock-off
position as shown in fig. 6A.
7. To Release Pressure
1 Do: With pump facing away, turn locked handle counterclockwise until air begins to escape. Stop turning
handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed with
water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
5C
5F
Pump until you feel
resistance.
6A
Lock
Trigger