Kohler Sterling 5300EZ Serie Instrucciones De Instalación Y Cuidado Para El Usuario

Sliding Bath Doors Sliding Shower Doors
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310 SterlingPlumbing.com
Critical Information!
Read Before Installation!
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass with tools or
any other hard objects. Do not set the unframed tempered glass directly on
the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
NOTICE: The warranty does not apply to a product that has been modified
or altered in a manner other than as expressly permitted in the Installation
and Care Guide.
Walls must be within 3/8" (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's instructions for application and
curing time.
To watch this installation online, visit the product page at
www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Read and follow all instructions.
IMPORTANT! The wall jambs must rest flat
1
against the shower ledge and the wall.
Determine which end of the wall jambs will rest
on the shower ledge. Match either the square or
contoured end of the wall jambs to the corner
radius of the shower ledge.
Contoured
End
Square
End
Using the large hex wrench (provided), turn the
6
expansion mechanism toward the inside of the
shower until the bottom track is secure, and the
wall jambs are flush against the shower walls.
Hex
Wrench
Expansion
Mechanism
1278968-2-A
Required Tools
Masking Tape
100% Silicone Sealant
Shop Vacuum
Remove the adhesive backing from both friction
2
pads. Attach a friction pad to the backside of
each wall jamb approximately 1" (25 mm) above
the shower ledge.
Adhesive
Backing
1"
Friction Pad
(25 mm)
Slide both caps toward the center of the top track.
7
Position the top track to rest on top of the wall
jambs, with the rounded face toward the outside
of the shower, and the expansion mechanism on
the right.
Expansion
Top Track
Mechanism
Top Track
Cap
Outside
of the
Shower
Parts Identifi cation
1277031-*
Hardware Pack
1204280-04** (5365EZ-45, 5375EZ-45)
1204280-03** (5375EZ-47)
1204280-02** (5325EZ-57, 5375EZ-57)
1204280-01** (5305EZ-59, 5325EZ-59)
Top Track Assembly
1205305**
Hanger Bracket Kit
#8-32 x 3/8"
1199426-01**
Hanger Bracket
1050048-B
Barrel Nut
1232118-58
Top Bumper
8-32 x 1/4"
1233169-01** (5305EZ)
1233169-02** (5325EZ)
1233169-03** (5375EZ)
1233169-04** (5365EZ)
Wall Jamb
1232119-58
Bottom Left
Bumper
1008723
Friction Pad
Center the wall jambs on the shower ledge.
3
Position both wall jambs the same distance from
the front and back edges.
Same Distance
Wall Jamb
Top View
NOTE: The clamp tabs must press the wall
8
jambs flush against the wall when the top track is
expanded.
When positioning the top track, insert the clamp
tabs against the wall jambs.
Top Track
Expansion Mechanism
Clamp Tab
Wall Jamb
1
Installation and Care Instructions
5300EZ Series Sliding Shower and Bath Doors
*Need help? Contact the STERLING Customer Care Center
Series Number Label
1051142-A
Screw
1044585
Roller
1199110
Gasket
1077763-A
Bolt
1093027
Spacer (8 ea.)
1057704-03** [18" (457 mm)]
1057704-02** [20" (508 mm)]
1057704-01** [24" (610 mm)]
Towel Bar
Door Panel*
1016785-04** (5365EZ-45, 5375EZ-45)
1016785-03** (5375EZ-47)
1016785-02** (5325EZ-57, 5375EZ-57)
1016785-01** (5305EZ-59, 5325EZ-59)
Bottom Track
Using a level, plumb both wall jambs. Secure
4
with masking tape.
Use the large hex wrench (provided) to turn the
9
expansion mechanism. Expand the top track
until the top track is secure, and the wall jambs
are flush against the shower walls. Tighten one
or two additional turns to secure the top track.
Remove the tape from the wall jambs.
Expansion Mechanism
Tape
at 1-800-STERLING (1-800-783-7546).
For service parts information, care and cleaning, and
other information, visit www.sterlingplumbing.com
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Wall Jamb*
1232118-58
Top Bumper
1008723
Friction Pad
1232120-58
Bottom Right
Bumper
1228730**
Guide
Set the bottom track on the shower ledge.
5
Position the bottom track between both wall
jambs with the bottom track leg facing the
outside of the shower.
Bottom Track
Leg
Outside of
the Shower
Press the top and bottom bumpers into place as
10
shown. Make sure the top bumper tabs press
directly into the triangular pockets in the clamps.
Top
Bumper
Bottom
Bumper