Tabla de contenido
Idiomas disponibles
Idiomas disponibles
SPECIFICATIONS
valid at 23 deg. C after a 30 minute warm-up period
DC voltages
Measurement ranges:500 mV, 5 V, 50 V, 500 V, 600 V
Resolution:
10 µV, 100 µV, 1 mV, 10 mV, 100 mV
Accuracy:
5 V, 500 V, 600 V:
±(0.05% of rdg.
500 mV, 50 V:
± (0.05% of rdg.
Overload protection:
V/Ω/T°/dB/
against COM and to chassis:
850 V
Low against chassis: 250 V
Input resistance:
50 V, 500 V, 600 V:
10 MΩ II 90 pF
>1 GΩ II 90 pF
500 mV, 5 V:
Input current:
10 A
≥100 dB (50/60 Hz ± 0,5%)
3)
CMRR
:
≥ 60 dB (50/60 Hz ± 0,5%)
4)
SMRR
dB Mode
Accuracy:
±(0,02 dB + 2 digits)
(display > –38,7 dBm)
Resolution:
0.01 dB above 18% of fs.
DC current
Measurement ranges:500 µA, 5 mA, 50 mA, 500 mA, 10 A
Resolution:
10 nA, 100 nA, 1 µA, 10 µA, 1 mA
Accuracy:
0.5 – 500 mA:
±(0.2% of rdg.
10 A:
±(0.3% of rdg.
Voltage drop:
10 A range:
0.2 V max.
500 mA range:
2.5 V max.
other ranges:
0.7 V max.
AC voltage
Measurement ranges: 500 mV, 5 V, 50 V, 500 V, 600 V
Resolution:
10µV, 100 µV, 1 mV, 10 mV, 100 mV
Accuracy 0,5-50 V:
40 Hz - 5 kHz:
± (0.4% of rdg.
20 Hz - 20 kHz:
± (1% of rdg.
500 V and 600 V:
40 Hz - 1 kHz:
± (0.4% of rdg.
20 Hz - 1 kHz:
± (1% of rdg.
Overload protection:
V/Ω/T°/dB/
against COM and to chassis:
850 V
Low against chassis: 250 V
Input impedance
AC mode:
AC + DC mode:
Bandwidth at -3 dB: 80 kHz typical
dB Mode:
20 Hz - 20 kHz
Accuracy
–23,8 – 59,8 dBm:
±0.2 dBm
Resolution:
0.01 dB above 9 mV
≥ 60 dB (50/60 Hz ± 0,5%)
3)
CMRR
:
Crest factor:
7 max.
AC current
Measurement ranges:500 µA, 5 mA, 50 mA, 500 mA, 10 A
1)
2)
+0.002% of fs.
)
1)
2)
+ 0.004% of fs.
at max.60 Hz or 600 V
p
DC
at max. 60 Hz or 250 V
rms
DC
2)
1)
2)
+ 0.004% of fs.
),
1)
2)
+ 0.004% of fs.
)
1)
2)
+ 0.07% of fs.
)
1)
2)
+ 0.07% of fs.
)
1)
2)
+ 0.07% of fs.
)
1)
2)
+ 0.07% of fs.
)
at max.60 Hz or 600 V
s
DC
at max. 60 Hz or 250 V
eff
DC
1 MΩ II 90pF
10 MΩ II 90pF
Resolution:
Accuracy
0.5-500 mA: ±(0.7% of rdg.+0.07% of fs.) for 40Hz-5kHz
10 A:
± (1% of rdg.
AC + DC measurements
Same as AC + 25 Digits
Resistance
500 Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 50 MΩ
Ranges:
Resolution:
Accuracy:
)
500 Ω to 500 kΩ: ±(0.05% of rdg.
5 MΩ and 50 MΩ: ± (0.3% of rdg.
Input protected to max. 300 V
Measurement current
500 Ω – 5 kΩ-range: 1 mA
50 kΩ-range:
500 kΩ-range:
5 - 50 MΩ-range:
Measurement voltage
10 V typical for open inputs, depending on the value of
resistance to be measured. Negative polarity of
measurement voltage is across common terminal.
Temperature
2-wire resistance measurement with linearization for
PT100 sensors as per standard EN60751
Range:
Resolution:
Measurement current: ca. 1 mA
Display:
Accuracy:
Temperature coefficient: (Reference 23°C)
V =
500 mV, 50 V
600 V range
other ranges
V ~
600 V range
other ranges
mA
all ranges
mA- all ranges
Ω
5 MΩ, 50 MΩ-ranges
other ranges
Miscellaneous
Operating conditions: + 10°C to + 40°C
max. rel. humidity: 80% (without condensation)
Power supply (from HM8001-2):
+ 5 V
~26 V
Size (W x H x D):
Weight:
1)
rdg. = reading;
2)
fs. = full scale;
Included in delivery: Manual, HZ15 PVC Test Leads.
Accessories: HZ10 Silicone Test Leads, HZ812
PT100 Temperature Sensor
Subject to change without notice
S p e c i f i c a t i o n s
10 nA, 100 nA, 1 µA, 10 µA, 1 mA
1)
2)
+ 0.07% of fs.
)
10 mΩ, 100 mΩ, 1Ω, 10Ω, 100Ω, 1 kΩ
1)
+0.004% of fs.
1)
+0.004% of fs.
eff
100 µA
10 µA
100 nA
–200 °C to +500 °C
0.1°C
in °C, °F
± 0.1 °C from –200 °C to +200 °C
± 0.2 °C from 200 °C to 500 °C
(except for sensor tolerance)
30 ppm/°C
80 ppm/°C
20 ppm/°C
80 ppm/°C
50 ppm/°C
200 ppm/°C
300 ppm/°C
200 ppm/°C
50 ppm/°C
300 mA
140 mA
135 x 68 x 228 mm
(without flat 22-pole connector)
ca. 500g
3)
= Common mode rejection ratio;
4)
= Serial mode rejection ratio
2)
+50mΩ)
2)
)
21
Capítulos
Tabla de contenido
