john deer Select X300 Serie Manual De Usuario

Kit pour paillis 42 pouces
Idiomas disponibles
  • ES

Idiomas disponibles

Enlaces rápidos

(Includes English, French, German, Spanish and Italian)
M154583
I5
42-Inch mulch
M154583
42-INCH MULCHING KIT
Litho in U.S.A.
BM21816
Parts In Kit
Qty.
Description
1
Mulch Plug
1
Retainer
1
Wingnut, Locking
1
Carriage Bolt
1
Washer, Slotted Oblong
2
Blade, Mulching
NOTE: Retain these installation instructions with your
machine operator's manual.
Mulch plug is shipped with carriage bolt, slotted
oblong washer and retaining clip pre assembled and
should not be removed from mulch plug. Wing nut is
shipped pre assembled on carriage bolt.
Parking Safely
1. Stop machine on a level surface, not on a slope.
2. Disengage mower blades or any other attachments.
3. Lower attachments to the ground.
4. Lock the park brake.
5. Stop the engine.
6. Remove the key.
7. Wait for engine and all moving parts to stop before you
leave the operator's seat.
8. Close fuel shut-off valve, if your machine is equipped.
9. Disconnect the negative battery cable or remove the
spark plug wire (for gasoline engines) before servicing the
machine.
John Deere Worldwide Consumer & Commercial Equipment Division
Litho in U.S.A.
Product Services Information
INSTALLATION INSTRUCTIONS
English - 1
Remove Mulching Blades
c
CAUTION: Avoid injury! Mower blades are
sharp. Always wear gloves when handling
mower blades or working near blades.
1. Lock the mower deck in the up position.
2. To prevent blade from turning during removal of the
attaching hardware, place a block of wood between blade
and deck. Rotate the blade until block of wood is tight
between mower deck and blade.
3. Remove blades:
John Deere Select Series™ X300 Models:
C
B
a. Remove and nut (A), beveled washer (B), and blade
(C). Repeat for other blade. Keep the blades for side
discharge mowing.
LT, and LX/GT Models:
E
D
a. Remove and retain bolt (A), washer (B), bevel
washer (C) and the blade. Repeat for other blade. Keep
the blades for side discharge mowing.
4. Deck must be clean to ensure proper fit of mulching kit.
Remove all grass build-up from underside of mower deck,
especially at the top and front surfaces. Clean inside the
mower deck lip groove around the discharge chute. Rinse
D
A
MX35989
C
B
A
M88112G
M154583 I5 (10/27/05)
Tabla de contenido
loading

Resumen de contenidos para john deer Select X300 Serie

  • Página 10: Extracción De Cuchillas Para Pajote

    Product Services Information INSTRUCCIONES DE INSTALACIÓN (Incluye inglés, francés, alemán, español e italiano) Extracción de cuchillas para pajote M154583 42-Inch mulch JUEGO DE PAJOTE, 42 IN. PRECAUCIÓN: ¡Evitar lesiones! Las cuchillas BM21816 de corte están afiladas. Usar guantes siempre que se manipulen las cuchillas de corte o al trabajar cerca de ellas.
  • Página 11: Instalación Del Tapón Para Pajote

    4. La plataforma deberá estar limpia, para asegurar un ajuste adecuado del juego de pajote. Quitar todas las acumulaciones de césped debajo de la plataforma de corte, especialmente en las superficies delantera y superior. Limpiar el interior de la ranura del borde de la plataforma de corte, alrededor de la tolva de descarga.
  • Página 12: Instalación De Cuchillas Para Pajote

    2. Instalar la arandela achaflanada (C) y sujetarla con una tuerca (D). Apretar la tuerca a 68 N•m (50 lb-ft). Repetir el procedimiento para la otra cuchilla. Modelos LT y LX/GT: NOTA: Instalar la arandela achaflanada con el lado acopado hacia arriba. MX11515 8.

Este manual también es adecuado para:

LtLxGt

Tabla de contenido