Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Description of the machine
The AH 80 PROXXON surface planer is a device for fine
planing work that is used to plane the irregular or rough
surface of a work piece and to plane it at right angles
(planed) as necessary.
The knife shaft with two high-quality HSS knives and an
operating speed of 6000 revolutions per minute ensure a
particularly even and smooth finish for work pieces con-
sisting of hard and soft wood types.
The power of the motor is transferred to the knife shaft
by a carefully coordinated toothed belt drive which
guarantees outstanding low vibration and a long life
cycle.
The sturdy, angle and cross adjustable longitudinal stop
enables high flexibility when determining the processing
width or the processing angle: This allows you to manu-
facture precise mitres using the previously adjusted
angle.
The supporting construction of the plane consists of
solid die-cast aluminium, guaranteeing the greatest sta-
bility.
All parts have been carefully processed and assembled
and thus guarantee a maximum of precision and long
life cycle.
The Proxxon team wishes you joy and success when
working with your electrical device!
Scope of delivery
1 piece Surface planing machine AH 80
1 piece Push-rod
1 piece Operating instructions
1 piece Brochure with safety guidelines
1 piece Rubber connector
Technical data:
Voltage:
Frequency:
Capacity:
Short-term operation
Max. planing width:
Length of planing table:
Rotational diameter of shaft:
Plane knife length:
Knife tooling:
Plane shaft speed while idling:
Max. chip removal:
Sound pressure level:
Sound power level:
- 14 -
220 – 240 Volt
50 Hz
200 watt
15 min
80 mm
approx. 350 mm
48 mm
82 mm
2 pieces HSS reverse knife
6000 U/min-1
0.8 mm
approx. 83,9 dB(A)
approx. 96,9 dB(A)
General measuring uncertainty
Vibrations:
Dimensions:
Length:
Height:
Width:
Weight:
Only to be operated in closed rooms!
Do not dispose of the electrical device in the
household waste!
Always work with hearing protection!
Set and commissioning:
Possibility of unexpected start-up! This could cause cut
injuries.
Therefore, always disconnect the mains plug for all
adjustment and maintenance work!
Setting up the device (fig. 2)
Please check the device for any signs of damage due to
transportation immediately upon unpacking! Damaged
packaging may already indicate improper handling dur-
ing transportation. Damage due to transportation must
be claimed immediately with your dealer or the corre-
sponding transport company!
Always handle the device only as shown in Figure 2a!
The surface for setting up the planer must be firm, clean
and dry.
1. To set up the planing machine, remove it from the
packaging and set it up on a straight and level sur-
face. Make sure it is stable and that the machine can-
not fall down during work.
2. Please note: The planer may only be operated if
screwed securely to the surface! The die-cast alu-
minium base of the device has 4 drill holes 1 with a 6
mm diameter for this purpose (see fig. 2). We recom-
mend M6 or M5 cheese-head screws or other appro-
priate screws (Item 2).
Adjusting the planing depth (Infeed) Fig. 3:
The twist grip (Fig. 3) is used to adjust the planing depth.
The set planing depth can be read on Scale 2 at the
front side of the table.
≤ 2.5 m/s2
approx. 350 mm
approx. 180 mm
approx. 220 mm
approx. 5.2 kg
Çaution:
Çaution
Caution:
Çaution !
K=3 dB
Capítulos
Tabla de contenido
