Tabla de contenido
Idiomas disponibles
Idiomas disponibles
OPERATING MANUAL & PARTS LIST FOR 791-5222, 791-5223
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
WARNING
Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS could
cause accidents resulting in serious or fatal personal injury and/or property damage.
SETUP
MODEL 791-5222 CAR DOLLY
PleASe ReFeR To THe eXPloded VIeW dRAWING IN THIS MANUAl IN oRdeR To IdeNTIFY PARTS.
1.
Press the foot pedal down with one hand while releasing the latch. The pedal is spring loaded, so remove your hand from the pedal slowly
and carefully.
2.
Remove the lock pin from the holes that secure the square telescopic tubes together.
3.
Install the hexagonal ends of the #3 rod assemblies into the receivers of the #8 inner and #13 outer body axle assemblies and secure
each with the #10 washer, #11 lockwasher and #4 bolt.
4.
Air may become trapped in the hydraulic system during shipping and handling. An air trapped system will not work properly and the jack
will not respond to a full incremental pump stroke of the pedal. In the event of an air trapped system, follow this procedure:
a.
The release valve knob is in the closed position when turned all the way in a clockwise direction until it stops. Turn the release valve
knob in a counterclockwise direction two full rotations.
b.
Pull the roller arms apart as far as they will travel.
c.
Pump the foot pedal about 15 times.
d.
Turn the release valve knob in a clockwise direction until it stops and start pumping.
e.
If the condition seems better but still trapped with air, repeat steps "a" through "d" until the system is fully purged of air.
MODEL 791-5223 CAR DOLLY RACK
PleASe ReFeR To THe eXPloded VIeW dRAWING IN THIS MANUAl IN oRdeR To IdeNTIFY PARTS.
1.
Install the four swivel casters to the left and right base arms and secure them with the locknuts as shown in the exploded view drawing.
2.
Install the left and right base arms to the receiver crossmember and secure them with the bolts and locknuts as shown in the exploded
view drawing.
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury and/or property damage.
MODEL 791-5222 CAR DOLLY
1.
Make sure the vehicle is on a hard, flat, dry surface and the transmission is in PARK or engaged in a gear if a manual transmission before
using the dollies.
2.
Open the release valve knob by turning it two complete revolutions in a counterclockwise direction. Pull the roller arms far enough apart
where they will straddle the vehicle's tire.
3.
Push the dolly in toward the tire where the roller arms are straddling the tire and the center of the tire seems to be in line with the center
of each roller arm.
4.
Turn the release valve knob in a clockwise direction until tight. Activate the foot pedal so the roller arms start approaching the tire and
check to see the dolly roller arms are properly aligned with the tire.
5.
Continue to activate the foot pedal until the tire is lifted at least 1" off the ground.
6.
Repeat steps 1 through 5 on the remaining three tires.
7.
Once the vehicle is supported by the dollies, move the vehicle slowly and carefully.
8.
Lowering a tire to the ground can be achieved by slowly and carefully turning the release valve knob in a counterclockwise direction.
Making sure the dolly's lift arms are not applying pressure on the tire, the dolly can then be pulled away from the tire. The remaining three
tires can be lowered following this same procedure.
MODEL 791-5223 CAR DOLLY RACK
1.
Make sure the car dolly is in the fully retracted position and the locking pin is engaging the telescopic tubes before installing on the rack.
2.
Make sure the foot pedal is depressed and secured with the hook latch.
3.
The previous steps must be completed before installing the dolly on the rack.
4.
Install the first dolly on the end of the rack. The second dolly should be installed next to the first dolly and so on until all four dollies are
installed as shown in the picture on page 1.
5.
The loaded rack can be moved by pushing or pulling on the hydraulic pump ends of any of the dollies slowly and carefully. Keep feet clear
of rack and swivel caster wheels.
791-5222, 791-5223
3
rev. 03/14/12
Tabla de contenido
