Idiomas disponibles
Idiomas disponibles
US
Information for use
sera reptil LED energy light
Please read these instructions carefully and keep for future use.
Thank you for choosing a sera reptil LED energy light.
This universal clip lamp is suited for terrariums that are open on
top, for aquaterrariums and for nano aquariums. The extremely
energy saving lamp unit consists of 72 extra long lived light
emitting diodes, 24 of which are blue. The blue LEDs (moon-
light) can be switched separately from the white ones (daylight).
The voltage at the lamp is only 12 V due to using a transformer
integrated in the plug. The sera reptil LED energy light is sim-
ply attached to an edge and clips up to 15 mm (0.6 in.) materi-
al thickness. The flexible goose neck allows easy adjustment of
the lamp head.
SAFETy PRECAUTIoN!
Please be sure to read carefully!
Do not look directly into the LED light from a short distance!
This may cause eye damage!
Application and application range
The clip holder allows for universal use up to 15 mm (0.6 in.) ma-
terial thickness. The sera reptil LED energy light is well suited
especially for open aquaterrariums. Special zones of the setup
can be lighted in a directed way in case of larger aquaterrariums.
Kit includes (fig. 1)
1.1
LED energy light
1.1.1 Lamp head
1.1.2 LED lamps blue/white
1.1.3 Goose neck
1.1.4 Clip holder with switch
1.2
Transformer with cable and 12 V DC plug 5.5 mm (0.2 in.)
Assembly instruction and operation (fig. 2)
Select an edge (2.1) onto which the lamp is to be installed. The
fastening screws of the clip holder (2.2) are loosened by a little
more than the material thickness. Push the clip holder onto the
edge and fasten the screws by hand. The 12 V DC plug is
pushed into the opening underneath the clip holder (2.3). Now
the ballast can be plugged into the mains socket. Use the tog-
gle switch (2.4) for selecting: In position "I", only the blue LEDs
for moonlight are switched on. In position "II", all LEDs are
switched on for daylight.
Cleaning
The casing of the sera reptil LED energy light can be wiped
with a slightly moist cloth. Do not use any organic solvents or
abrasive cleaners.
Maintenance
In case some of the LEDs should fail after a longer time, you can
still operate the lamp. The LEDs are connected in a way that al-
lows up to three LEDs to fail at the same time. The function of
the other LEDs is not affected. The LED lamp unit should be re-
placed if the light intensity of the lamp is not sufficient any more.
Replacing the LED lamp unit (fig. 3)
Loosen the 4 screws (3.1) at the bottom side of the lamp. Take
the LED holder plate with the LED lamps (3.2) out of the socket
(3.3). Pull the plug connections apart. Insert the new LED hold-
er plate with the LED lamps in reverse order.
Technical Data
Uptake: approx. 8 W incl. transformer
Lamps:
48 white LEDs
24 blue LEDs
Transformer:
In: 100 – 240 VAC
Output: DC 12 V 0.5 A
Spare parts
LED holder plate with LED lamps (3.2)
Transformer 12 V 0.5 A with 2 m (6.6 ft.) cable (1.2)
Warning
1. Children should be supervised to ensure that they do not
play with the appliance.
2. This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental ca-
pacities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
3. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
Disposal of the unit:
Waste electrical and electronic equipment (WEEE) must not
get into domestic waste!
If ever the unit cannot be used anymore, the consumer is legal-
ly obliged to hand in waste electrical and electronic equip-
ment (WEEE) separately from domestic waste, e.g. at a col-
lection point of his community/his district. This ensures that
waste electrical and electronic equipment (WEEE) is expertly
processed and that negative effects to the environment are
avoided.
Therefore electrical and
electronic equipment bears the following symbol:
6
