Electrical Connection Diagram; Operation Modes - Astralpool 35450 Manual De Instalación Y Mantenimiento

5.1. Colorplus ECO: pushbutton control
The system has 14 operation modes: 7 set colours and 7 sequences of different colours (see section 6.1.2.) The colour or sequence
is changed by a quick press of the pushbutton. The projector/s is/are placed in white if the pushbutton is pressed for longer.

5.1.1. Electrical connection diagram

The Color Plus Eco system is composed of the projector/s, the transformer and the normally closed (NC) pushbutton.
The transformer must be able to supply 60VA for each led spotlight connected. For example, if you want to control 6 spotlights, you
must connect them in parallel to a transformer of at least 270VA. The pushbutton must be able to withhold the power consumed by
the number of projectors installed.

5.1.2. Operation modes

The Colorplus ECO unit enables different light scenarios to be created inside the swimming pool with two operation possibilities:
Set colour: Selection of one set colour out of seven possibilities.
COLOUR Nº
Automatic sequence of colours: Selection of nine colour sequence programmes. Each programme is defined by the lighting time of
each colour and the transition time from one colour to another according to the following table:
SEQUENCE
1 Red
2 Red
3 Purple
4 Red
5 Purple
6 Yellow
7 Green
The colour or sequence is changed by pressing the pushbutton. The colour and sequence cycle is rotary. For example, if you are in
colour 5, by pressing once, you will reach colour 6. If you press once again, you will go to sequence 7. If you are in sequence 7,
press once and you will get to colour 2, which is Red.
Colour 1, corresponds to white and is reached by one long press.
5.2. COLOR PLUS TOP: Receiver-Modulator control and/or Remote control
The system has 21 operation modes: 12 set colours and 9 sequences of different colours (see section 6.2.2.).
The Receiver-Modulator controls switching the spotlights on and off, changes of colour and sequences and switching off timing.
If you have a remote control, apart from the receiver-modulator operations, you can also switch colours of a sequence on and off and
select the switching off time.
5.2.1. Electrical connection diagram
For correct installation, you will need the Receiver-Modulator, the transformer and finally the leds lamp. As an option, this system
can be controlled by Remote Control. For more information on the installation of the Receiver-Modulator, see point 6.2.3. and section
6.2.4. includes information on the Remote Control.
The Receiver-Modulator is connected to the 230 Vac mains by means of two terminals indicated MAINS, and to the primary input of
the transformer (230 Vac) by means of the terminals indicated TRF (See attached diagram).
Each Receiver-Modulator, it can control until a maximum of five spotlights.
The transformer must have the capacity to supply 60 VA to each led spotlight connected. For example, if you want to control 5
lamps, they should be connected in parallel to a transformer of at least 270VA.
Each Receiver-Modulator can control up to a maximum of 15 LED spotlights.
% RED
1 100
2 100
3 0
4 0
5 100
6 0
7 100
ORDER OF COLOURS
Blue Green Purple
Green Cyan Blue
Cyan Yellow -
Blue Green -
Cyan Yellow -
Purple Cyan -
Red Blue -
% BLUE % GREEN
100 100
0 0
100 0
0 100
100 0
100 100
0 100
COLOUR TIMING
Cyan Yellow
Purple Yellow
- -
- -
- -
- -
- -
3
COLOUR
White
Red
Blue
Green
Purple
Cyan
Yellow
BLENDING TIMING
(SEC.) (SEC.)
2
4
4
8
18
0,5
0,5
2
4
4
8
18
0,5
0,5