e-conolight ECONOLED Instrucciones De Instalación página 4

Install Mounting Brackets (optional)
(A)
Mark Placements for Brackets
12" – 16"
12" – 16"
Install Edge Bracket
(A)
(A)
(A)
Install Channeling
(A)
(A)
(A)
IMPORTANT
(A)
The LED Flexible Cable Strip Lighting system is designed to work ONLY
with the power supplies, connectors, mounting options, and accessories
listed. Do NOT substitute other products as they may damage your system.
Do not plug into outlet until power supply is secured. Place power supply
near outlet and off the ground so there is no chance of it being submerged in
water. Risk of fire and electric shock. Uncoil LED Cable strip prior to plugging
into receptacle. The connectors consist of two parts: a top and bottom,
which are partially assembled at the factory. Do NOT push the connectors
together before you are ready to install. The LED Cable strip may only be
cut every 7 inches, indicated by a cut line on the LED side of the strip. When
you are measuring for your installation, if the total length in inches is not a
multiple of 7, then adjust the plan of your layout to use the nearest cut line
marked on the strip. When using pliers that do not cover the entire surface
of the connector, hold the connector and strip steady so the LED Cable strip
remains in position. Carefully rotate the pliers and apply pressure to each
side of the connector, pushing the top and bottom together. There is only one
way to connect the 4-way Power Splitter/Power Supply (PS) Link Connector
to the Power Supply. Make certain the icons match before connecting.
Connect the 4-way Power Splitter to the PS Link Connectors and to the
Power Supply BEFORE plugging the power supply into the AC outlet. Do not
coil the strip into a tight circle with a diameter less than 8 inches.
ELECTRICAL RATING
To avoid any malfunctions of the system, and to protect against electrical
shock, fire, or physical injury, please observe the following: This system has
been designed to work with 100-240 volt AC current. Connection to a line
voltage other than that may create a safety and fire hazard and may damage
the system. If you are unsure of the type of power supply to your home,
consult your local power company or a qualified service technician.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances. WARNING – Improper
connection of the equipment-grounding conductor is able to result in a risk
of electric shock. Check with a qualified electrician or serviceman if you are
in doubt as to whether the product is properly grounded. Do not modify the
plug provided with the product. If it will not fit the outlet, have a proper outlet
installed by a qualified electrician. Ground Fault Circuit Interrupter (GFCI)
protection should be provided on the circuits or outlet to be used for outdoor
use of this product. Receptacles are available with built-in GFCI protection
for this measure of safety. If you are unsure of the type of outlet, consult a
qualified service technician to install a GFCI receptacle.
(B)
(B)
(B)
(B)
(B)
(B)
(B)
POWER SOURCE
(B)
Do not modify the plug provided with this product. If it will not fit the outlet,
have a proper outlet installed by a qualified electrician. Damaged or
deformed power cords are hazardous and should be replaced immediately
by a qualified service technician.
OPERATION
Do not operate with the LED Cable strip tightly coiled. Do not puncture,
cut, shorten, or splice the LED cable strip (except where marked). Unplug
the unit and AC power adapter from the electrical outlet during electrical
storms or when unused for long periods of time to prevent damage. For
outdoor use, make sure that all connections and the end cap in the last
segment are tightly secured to preclude the entry of water. Do not exceed
the recommended length of LED cable listed for each power supply. Do not
look directly into the LEDs when lit. They are powerful and could damage
your vision.
LOCATION
Place power supply well above the ground or in an area they will NOT be
submerged in water or other liquids. The LED Cable strip and components
are rated IP65, weatherproof only. Do not submerge the LED cable strip in
liquids, or use the product in the vicinity of standing water or other liquids.
Keep all components away from extreme heat sources such as heating
vents, radiators, electric heaters, and fire pits. Do not cover this product
as the covering may cause the LED Cable to overheat, melt, or ignite. Do
not submerge the LED Cable in liquids, or use the product in the vicinity of
standing water or other liquids. Do not route the cord or LED Cable through
walls, doors, windows, or any like part of the building structure. Place LED
Cable strip so it will not shine directly into people's eyes.
INSTALLATION
Safety measures must be observed at all times during the installation of this
product. Use proper safety gear and tools during the installation process
to prevent physical injury. Products should be installed in accordance
with the user manual, current electrical codes and/or the current National
Electric Code (NEC). Improper installation may cause a possible shock or
fire hazard. To avoid electrical shock and/or damage to the system, do not
handle the components with wet hands. Always make sure the LED Cable
strip is disconnected from the power source before cutting, connecting,
mounting, or modifying in any way. Do NOT dismantle the LED Cable strip
itself. Do not coil the strip into a tight circle with a diameter less than 8 inches
or bend it in half as it may damage the LEDs embedded in the LED Cable
strip. Do not subject the LED Cable strip to continuous flexing. Do not use if
there is any damage to the light or cord insulation. Inspect periodically. LED
Cable connectors have sharp pins inside. Follow instructions when handling.
Use only e-conolight LED Cable connectors, mounting, and power supply.
Carefully follow the instructions to install and mount. Secure the LED Cable
using only the hangers or clips provided. Do not secure this product or its
w w w . e - c o n o l i g h t . c o m | s a l e s @ e - c o n o l i g h t . c o m | 8 8 8 . 2 4 3 . 9 4 4 5
Installation Instructions
12" – 16"
Install Channel Bracket
(A)
(C)
(A)
Adjust placement, if
necessary, when tightening
screws.
(A)
Snap into lip
(C)
cord with staples, nails, or like means that may damage the insulation.
(C)
CLEANING
Clean only with a dry or slightly damp cloth. DO not use any acid or alkaline
liquids, cleansing agents, or solvents. Unplug the system from the wall outlet
before cleaning.
NON-USE PERIODS
When left unused for long periods of time, the system should be unplugged
from the AC outlet.
SERVICE
Always remove the AC power adapter from the electrical outlet before
adjusting or inspecting the system. Inspect your system periodically. Do not
open, dismantle, or attempt to repair the LED Cable strip or the bottom half
of the connectors. There are no user-serviceable parts. Do not open the
cabinets of accessories or power supply. Opening the cabinets may present
a shock hazard, and any modification to the product will void your warranty.
Do not attempt to service the components yourself. If water or any metal
objects such as paper clips, wire, or staples accidentally fall inside, then
disconnect from the power source immediately and consult an authorized
service center.
Technical data is based on optimum conditions and actual performance
may vary.
© 2012 e-conolight. All rights reserved.
Country of origin: China
U.S. Design Patent No. D635, 930 S
www.e-conolight.com
(B)
(B)
(B)
IP65
N25615