Troubleshooting - RIB RED Manual De Instrucciones

G
B
ADDING OTHER TRANSMITTERS (MAX. 6)
Should, once installation is complete, other transmitters be installed in
order to increase automation security levels, it is suggested to:
1 - Unplug system power feed.
2 - Secure the edge and the corresponding transmitter in the desired
position.
3 - Run programming by turning ON a different microswitch from the other
installed transmitters and identify it by the corresponding adhesive
label (see chapter on transmitter Coding and identification).

TROUBLESHOOTING

ALL RECEIVER LEDS ARE OFF
BUZZER BEEPS EVERY 3 SECONDS FOR 1 MINUTE, OR ONE OF
TWO-COLOUR LEDS IS STEADILY LIT RED
BUZZER BEEPS INTERMITTENTLY FOR 1 MINUTE EVERY 3 HOURS,
OR ONE OF THE TWO-COLOUR LEDS IS ALTERNATIVELY BLINKING
RED AND GREED
THE BUZZER GIVES AN ALTERNATING SOUND AND ON TWO-
COLOUR EDGE LED FLASHED RED/GREEN ALTERNATIVELY.
THE DL2 LED IS OFF AND ONE TWO-COLOUR EDGE LED GIVES A
FIXED GREEN LIGHT.
WHEN PRESSING THE EDGE AGAINST THE N.C. CONTACT, THE
BUZZER TURNS ON FOR 2 SECONDS AND THE DL1 AND DL2 LEDS
TURN OFF FOR 2 SECONDS.
WHEN PRESSING THE EDGE AGAINST THE N.C. CONTACT, THE
BUZZER TURNS ON FOR 2 SECONDS AND THE DL1 AND DL2 LEDS
TURN OFF FOR 2 SECONDS.
IF THE BATTERY IS REMOVED THE BUZZER DOES NOT GIVE ANY
SOUND
R
ED TECHNICAL FEATURES
RADIO EDGE RECEIVER ACG5501
- FREQUENCE
- SENSITIVITY
- OUTPUT POWER
- POWER FEED
- IDLE ABSORPTION
- MAX ABSORPTION
- MODULATION TYPE
- RANGE
- RELAY CAPACITY
- CASE
- SIZE
- PROTECTION LEVEL
- OPERATION TEMPERATURE From -20°C to +60°C
PROBLEM
868.3 MHz
-108 dBm
<25 mW
11÷24 Vac/dc
20 mA
100 mA
FSK
20 m IN FREE SPACE WITHOUT
AERIAL
1A - 30Vdc
External - Technopolimer
129x89x58 mm
IP56
4 - On the receiver, enable the microswitch controlling the newly-added
transmitter.
5 - Plug system power feed.
Run storage and check procedures as outlined above.
CHECK VOLTAGE BETWEEN 11 AND 24 VAC/DC AT POWER FEED
TERMINALS
REPLACE BATTERIES AS SOON AS POSSIBLE - THEY ARE ALMOST
FLAT
REPLACE FLAT BATTERIES
DISCONNECTED CABLES ON N.O. CONTACT EDGE
or
CHECK 8,2KΩ IN SERIES RESISTOR AT N.C. CONTACT EDGE
DISCONNECTED CABLES ON N.C. CONTACT EDGE
or
CHECK 8,2KΩ IN SERIES RESISTOR AT N.O. EDGE CONTACT
MAKE SURE THAT THE JP2 JUMPER ON THE TRASMITTOR WAS
SELECTED ON N.C.
MAKE SURE THAT THE JP2 JUMPER ON THE TRASMITTOR WAS
SELECTED ON N.O.
CHECK THE RECEIVER TO MAKE SURE THAT THE TRANSMITTOR
CONTROL MICROSWITCH IS ON
RADIO EDGE TRANSMITTER ACG6202
- FREQUENCE
- SENSITIVITY
- OUTPUT POWER
- BATTERY FEED
- IDLE ABSORPTION
- MAX ABSORPTION
- MODULATION TYPE
- RANGE
- BATTERY(IES) LIFE
- CASE
- SIZE
- PROTECTION LEVEL
- OPERATION TEMPERATURE
22
22
CHECK
868.3 MHz
-108 dBm
<25 mW
3 x AA1,5 V (> 2,7 Ah) or on demand
1 x LITHIO 3,6 V (>5,5 Ah)
25 uA
13 mA
FSK
20 m IN FREE SPACE WITHOUT
AERIAL
3 YEARS (AA TYPE)
4 YEARS (LITHIO TYPE)
External - Technopolimer
129x89x58 mm
IP56
From -20°C to +60°C