Mains Input - HK Audio 7 Serie Manual De Instrucciones

●
8
Preset
Use the Preset selection button to call up factory presets or a user preset
you can confi gure via the remote DSP CONTROL software. Tap the select
button once to scroll through Presets 1 through 4.
A separate manual explains how to program the four remote user presets.
You will fi nd it on the LINEAR 7 download page at www.hkaudio.com.
Presets:
L7 110 XA L7 112 FA
1 Flat Flat
2 Monitor Boost
3 Low Cut Low Cut
4 Remote (to access stored settings via the remote
HK Audio DSP CONTROL software)
The L7 FA/XA models' factory presets:
Flat Delivers linear response across the full frequency range
Monitor Optimized to dampen the extra bass generated by fl oor
coupling when you set a speaker on its side for use as a
monitor
Boost Enhances low-frequency response when you use the mid/
high unit a standalone speaker without a subwoofer
Low Cut A high-pass fi lter optimizes the unit for use as a mid/high
unit paired with the L7 118 Sub A
The L7 118 Sub A's factory presets:
Front Standard operating mode for a forward-facing subwoofer
Cardioid 1:1 For cardioid setups with one forward-facing L7 118 Sub A;
see section 4.2 for more on this
Cardioid 2:1 For cardioid setups with two forward-facing L7 118 Sub As;
see section 4.2 for more on this
Factory presets 1 to 3 address the speaker only and not the DSP Out.
Heads up: If you are operating the speaker in a network connected to
the remote DSP CONTROL software, you can confi gure the DSP Out
independently even when using factory presets 1 to 3. To learn more
about this, consult the separate DSP CONTROL manual. You will fi nd it
on the LINEAR 7 download page at www.hkaudio.com.
The Remote Preset
Remote This lets you call up a user preset that you previously stored
via DSP CONTROL for the speaker as well as for the DSP
Out. The speakers does not need to be connected to the
remote software to do this.
The remote preset's default setup is identical to factory preset 1 (Flat/
Front).
You can access the following DSP functions via the remote DSP CONTROL
software and save your settings in user presets:
Fully parametric 10-band EQ with variable fi lter characteristics for each
frequency band, high-pass and low-pass fi lters with variable fi lter
characteristics, Limiter, Delay, Polarity, Level, and Mute
You can confi gure these parameters separately and independently for the
speaker and its DSP Out.
L7 112 XA L7 115 FA L7 118 Sub A
Flat Flat Front
Monitor Boost Cardioid 1
Low Cut Low Cut Cardioid 2
Screenshot of the remote DSP CONTROL software. You can download this software free of charge at the
LINEAR 7 product page at www.hkaudio.com. The speaker and DSP Out parameters are identical, but
the powerful onboard DSP lets you configure each set independently.
●
9
Power
This rocker switch turns the power on and off . Set it to Power to turn the
electronic components on and to Off to disconnect them from the mains
power supply. The Power switch does not aff ect the Powercon Link port.
●
12
See section below for more on this.
●
10
Power-LED
This LED lights up green when the electronic
components are getting mains power.
●
11

Mains Input

Use the factory-included Powercon mains cord
to connect this socket to a power outlet. Insert
the push-pull connector and turn it clockwise to
make sure the Powercon cord engages and locks.
To unlock it, pull the Powercon plug's locking
mechanism towards the cable and turn it counterclockwise.
Power Mains Input
100-240 V~ 50-60 Hz
1.9 A @ 1/8 output power
9
●
12
Link
(L7 118 Sub A only)
This socket can power up to three additional LINEAR 7
speaker cabinets. Hardwired to the Mains Input, it is not
aff ected by the Power switch setting. The Link circuit
goes live the moment you connect the Mains Input to
a power source. This is why you must make sure all
downstream devices are switched off before you connect
them to the Link port.
LINEAR 7 1.1
10
Power
Auto Sleep
On Off
13
Link
100-240 V~ 50-60 Hz
max. 10 A
Lock Lock
11 12
5