Before Starting The Equipment; Continuous Operation - EINHELL TE-ID 650 E Manual De Instrucciones Original

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1. Fitting the additional handle
(Fig. 2-3/Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do
not use the tool without the additional handle.
The additional handle (8) is secured to the ham-
mer drill by a clamp. During the handle clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
•
The supplied additional handle (8) must
first be fitted. To do this, the clamp must be
opened by turning the handle until it is wide
enough for the additional handle to be slid
over the chuck (1) and on to the hammer drill.
•
After you have positioned the additional
handle (8), turn it to the most comfortable
working position for you.
•
Now turn the handle in the opposite direction
again until the additional handle is secure.
•
The additional handle (8) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop
(Fig. 4-5/Item 2)
•
Undo the thumb screw (a) on the additional
handle (8) and insert the depth stop (2) in the
hole of the additional handle.
•
Set the depth stop and retighten the thumb
screw.
•
Now drill the hole until the depth stop touches
the workpiece.
5.3 Fitting the drill bit (Fig. 6-7)
•
Always pull the power plug before making ad-
justments to the equipment.
•
Release the depth stop as described in 5.2
and push it towards the additional handle.
This provides free access to the chuck (1).
•
This hammer drill is equipped with a spindle
lock (9) and a quick-change drill chuck.
•
Press the spindle lock (9) and turn the drill
chuck (1) until it engages (see Fig. 6). Kee-
ping the spindle lock (9) pressed, turn the
firmly closed drill chuck (1) so that it opens
(see Fig. 7). The drill chuck opening must be
Anleitung_TE-ID_650_E_SPK7.indb 18 Anleitung_TE-ID_650_E_SPK7.indb 18
GB
large enough to take the drill bit.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Keeping the spindle lock (9) pressed, turn the
drill chuck (1) so that it closes. Check that the
drill bit is secure in the chuck (1).
•
Check at regular intervals that the drill bit or
tool is secure (pull the mains plug).
•
When the quick-change drill chuck (1) is open
as far as it will go (maximum drill bit opening)
and secure, press the spindle lock (9) and
turn the drill chuck (1) clockwise (viewed
from the front) until you hear a grating noise.
Keeping the spindle lock (9) pressed, turn the
drill chuck (1) approx. 5 mm in the opposite
direction until you hear a clicking noise. Then
turn the drill chuck (1) clockwise again to the
desired position. This function will prevent
damage to the drill chuck.
Important.
Do not press the spindle lock (9) while the drill is
in use.
5.4 Storage of the drill (Figure 1 / Item 10)
The additional handle (8) is equipped with a sto-
rage compartment for drill bits (10) where you can
store drill bits of diff erent sizes.
•
Turn the storage compartment (10) anti-clock-
wise and out of the additional handle (8).
•
Insert the required drill bits.
•
Mount the storage compartment (10) back on
the additional handle. When doing so, make
sure that the pins on the inner edge of the
storage compartment (10) fit onto the reces-
ses in the additional handle (8).
•
Secure the storage compartment by turning it
clockwise.
6. Operation
6.1 ON/OFF switch (Fig. 8/Item 5)
•
First fit a suitable drill bit into the tool (see
5.3).
•
Connect the mains plug to a suitable socket.
•
Position the drill in the position you wish to
drill.
To switch on:
Press the ON/OFF switch (5)

Continuous operation:

- 18 -
25.02.2021 09:22:10 25.02.2021 09:22:10