Before Proceeding; How To Use This Manual; About Operations In This Manual; Checking Supplied Accessories - Pioneer PDA-5001 Manual De Instrucciones

Before Proceeding

How to use this manual

This manual is set up to follow the course of actions and
operations in the order that would seem most logical for
someone setting up this unit.
Once the unit has been taken out of the box, and it has
been confirmed that all the parts have been received, the
section "Connecting this unit to the monitor" starting on
page 5 outlines the procedure for connecting this unit to
the plasma display, PDP-502MXE.
After the unit is connected to the plasma display, use this
instruction manual in conjunction with the instruction
manual included with the PDP-502MXE to control your
system
To familiarize yourself with the parts, buttons, and
controls of this unit, the plasma display, and the remote
control unit, please refer to the section "Part Names and
Functions" on page 3 and the corresponding section in
the instruction manual for the PDP-502MXE.
Once this unit is connected to the plasma display,
PDP-502MXE, the section "About the input jacks"
starting on page 7 covers all the necessary points
regarding connections to a wide variety of components.
The section "Setting Up the System" starting on page 14
covers the necessary on-screen menu settings to
establish correct linkage to connected components.
Depending on the connections made, this section may or
not be necessary.
The sections "Operations" and "Display Panel
Adjustments" starting on pages 17 and 21 respectively,
are dedicated to the basic operations associated with
selecting a source component as well as the more
complex operations associated with adjusting the plasma
display picture to match the requirements of specific
components and personal preferences.

About operations in this manual

Operations in this manual are outlined in step by step
numbered procedures. Most of the procedures are
written in reference to the remote control unit unless the
button or control is only present on the main unit.
However, if a button or control on the main unit has the
same or similar name as that on the remote control unit,
that button can be used when performing operations.
2
<ARE1351> En
The following example is an actual operation that shows
how one might set the brightness of the screen. The
screens shown at each step are provided as a visual
guide to confirm that the procedure is proceeding as it
should. Please familiarize yourself with this process
before continuing on with the rest of this manual.
1
Press MENU to display the menu screen.
2
Press 5/∞ to select PICTURE, and then press 3.
M A I N M E N U
P I C T U R E
S C R E E N
A L L R E S E T
P OW E R S A V E
S E T U P
M E N U : M E N U
O F F
: S E L E C T
3
Press 5/∞ to select BRIGHT, and then press SET.
M A I N M E N U
P I C T U R E
S C R E E N
A L L R E S E T
P OW E R S A V E
S E T U P
M E N U : M E N U
O F F
: S E L E C T
4
Press 2/3 to adjust the picture quality as desired.
P I C T U R E
B R I G H T
: A D J U S T
5
When the setup is finished, press MENU to exit
the menu screen.

Checking supplied accessories

Check that the following accessories were supplied.
1
Pin/BNC conversion adaptor x 1
2
Screw rivets x 8
3
Connector cover x 1
÷ Operating Instructions
C ON T R A S T : 0
:
B R I G H T 0
:
C O L O R 0
:
T I N T 0
:
S H A R P 0
R E S E T
C ON T R A S T : 0
B R I G H T : 0
C O L O R : 0
T I N T : 0
S H A R P : 0
R E S E T
:
S E T A D J U S T
0
S E T : E X I T