Troubleshooting; Specifications - Denon RCD-M33 Instrucciones De Operación

ENGLISH
14

TROUBLESHOOTING

Check the following once more before assuming there is a problem with the system.
1. Are connections proper?
2. Is the system being operated as explained in the operating instructions?
If the system does not seem to be operating properly, check as shown on the table below. If
none of these checks apply to the problem, the system may be malfunctioning. Disconnect the
power cord immediately and contact your store of purchase.
Symptom
Power does not turn on
• Power cord is not plugged into a
when power operation power outlet.
switch is pressed.
No sound is produced • VOLUME control is turned
from the speakers. down.
• Headphones are connected.
• Speaker cords are not securely
connected.
• Speaker polarities ( < and >)
No treble sound is
produced, or the are inverted.
position of the
instruments is unclear.
A source other than the • Function is not properly set.
desired one is heard.
Hissing sound is heard • Antenna direction is poor.
in FM programs.
• Signals from the broadcast
station are weak.
Hissing sound is heard • Noise from a TV or interference
in AM programs. from a broadcast station.
Humming sound is • Signals on the power cord are
heard in AM programs. being modulated by the power
source frequency.
Total number of tracks • Disc is loaded upside-down.
not displayed when • Disc is dirty.
disc is loaded. • Disc is not of the specified type.
Nothing happens when • Disc is loaded upside-down.
operating buttons are • Foreign object on disc tray.
pressed.
Disc stops in the • Disc is dirty.
middle of a track and • Disc is scratched.
will not play properly.
Sound is broken. • Dirt, fingerprints, spittle, etc. on
disc.
• Disc is scratched.
• Player is in an unstable place
and vibrates strongly.
Humming sound is • Signals on the power cord are
heard, when disc is being modulated by the power
played. source frequency.
"Not Support" is • A copyright-protected WMA file
displayed when playing or a file that cannot be played
MP3 or WMA files. properly is selected.
26
Cause Remedy
• Plug the power cord securely
into an outlet.
• Set the control to an appropriate
Position.
• Disconnect the headphones.
• Connect securely.
• Connect the speaker cords
properly.
• Set the desired function using
the FUNCTION button.
• Change the direction of the
antenna.
• Install an outdoor antenna.
• Turn the TV off.
• Change the direction of the loop
antenna.
• Install an outdoor antenna.
• Insert the power cord in the
opposite direction.
• Install an outdoor antenna.
• Reload the disc.
• Clean the disc.
• Replace with a disc of the
specified type.
• Reload the disc.
• Remove the disc and the foreign
object.
• Clean the disc.
• Replace with an unscratched
disc.
• Clean the disc.
• Replace with an unscratched
disc.
• Place the player in a stable place
with no vibrations.
• Insert the power cord in the
opposite direction.
9 8
• Use the and buttons
to select another file.
15

SPECIFICATIONS

Receiver section
Reception frequency band:
Reception sensitivity:
FM stereo separation:
Rated output power:
Audio input / output jacks:
page
6
CD player section
Wow & flutter:
7
Sampling frequency:
7
Optical source:
6
Analog Audio Output:
6 Clock, Timer section
Clock system:
Clock precision (per month):
Timer functions:
7
5
General
Power supply:
5
Power consumption:
Maximum external dimensions: 210 (W) x 95 (H) x 328 (D) mm
–
–
Mass:
5
Remote control unit (RC-999)
–
Remote control system:
Power Supply:
5
Maximum external dimensions: 49 (W) x 220 (H) x 25 (D) mm
11
Mass:
11
–
* Maximum dimensions include controls, jacks, and covers.
(W) = width, (H) = height, (D) = depth
11
11
• For improvement purposes, specifications and functions are subject to change without
advanced notice.
11
–
11
–
–
–
23, 25
FM : 87.50 MHz ~ 107.90 MHz
AM : 520 kHz ~ 1710 kHz
FM : 1.5 µV/75 Ω/ohms
AM : 20 µV
35 dB (1 kHz)
22 W + 22 W (6 Ω / ohms, 1 kHz, T.H.D. 10%)
TAPE input/output jacks, AUX input/output jacks,
MONO OUT
3.5 mm headphones jack
Below measurable limits (±0.001% W. peak)
44.1 kHz
Semiconductor
OUTPUT level : 1.0 Vrms (TAPE OUT, AUX OUT)
Power source synchronous system
± 30 seconds
Everyday timer (1 setting)
Once timer (1 setting)
Sleep timer (maximum 90 min.)
AC 120 V, 60 Hz
50 W
(including feet, controls and terminals)
4.3 kg (9 lbs, 8 oz)
Infrared pulse system
Two DC 1.5V R03/AAA batteries
120 g (including batteries)