Terminator
The following installation procedures are suggested
guidelines for the installation of the Terminator ECM-R-WP Kit.
Kit Contents . . .
1
2
3
Item
Quantity
Expediter Assembly
Support Cap with O-Ring
1
1
Threaded Grommet Compressor
Grommet
Support Base with O-Ring
2
1
Junction Box Lid
3
1
Junction Box Base with O-Ring
4
1
Nut
5
1
Banding
Electronic Control Module w/ Terminal Blocks
(Refer to terminal specifi cations for maximum allowable wire size)
ECM Type*
6
1
C - Controller
L - Limiter
CL - Controller/Limiter
* The maximum pipe exposure temperature is limited to 232°C
7
1
Junction Box Lid Cord
8
2
Blind Plug
9
1
Bracket
10
3
Screws
11
3
Washers
Order Separately . . .
PETK Power and End Termination Kits (per cable)
PETK-5
for direct connection
1
2
Item
Quantity
1
2
Conductor Wire Pin
2
2
Braid Wire Pin
3
2
Ground Sleeve
PETK-10
for cold lead connection (TESH 2.9-15)
PETK-11
for cold lead connection (TESH 17.8-8000)
2
1
Item
Quantity
1
2
Conductor Wire Pin
2
2
Braid Wire Pin
3
2
Ground Sleeve
3 m TESH CL-2,5 (PETK-11)
4
1
3 m TESH CL-6 (PETK-10)
TM
ECM-R-WP
4
5
6
7
8
10
9
Description
3
Description
3
4
Description
INSTALLATION PROCEDURES
Receiving, Storing and Handling . . .
1. Inspect materials for damage incurred during shipping.
2. Report damages to the carrier for settlement.
3. Identify parts against the packing list to ensure the
proper type and quantity has been received.
4. Store in a dry location.
Order Separately . . .
IEK Insulation Entry Kit (per cable)
IEK-TESH-1
11
IEK-TESH-2
IEK-RTD
Dimensions . . .
155mm
200mm
Warnings . . .
• Due to the risk of electrical shock, arcing and fi re caused
by product damage or improper usage, installation
or maintenance, a ground-fault protection device is
required.
• Installation must comply with Thermon requirements
(including form PN 50207U for Ex systems) and be
installed in accordance with the regulations as per the
norm EN IEC 60079-14 for hazardous areas (where
applicable), or any other applicable national and local
codes.
• Component approvals and performance ratings are
based on the use of Thermon specifi ed parts only.
• De-energize all power sources before opening enclosure.
• Avoid electrostatic charge. Clean only with a damp cloth.
• Keep ends of heating cable and kit components dry
before and during installation.
• Minimum bending radius of heating cable is 32 mm
(except HPT is 57 mm and FP is 19 mm).
• Individuals installing these products are responsible
for complying with all applicable safety and health
guidelines. Proper Personal Protective Equipment (PPE)
should be utilized during installation. Contact Thermon
if you have any additional questions.
Tools Required . . .
Crimp Tool 2,5mm
Certifi cations/Approvals . . .
IP66 -60°C Ta +50°C T5, 100°C; -60°C Ta +40°C T6, 85°C
Ordinary & Hazardous Locations
FMG 10.0022X Ex db eb IIC T5-T6, Ex tb IIIC T100°C-T85°C
International Electrotechnical Commission
IEC Certifi cation Scheme for Explosive Atmospheres
SIR 12.0103X
II 2 (2) G Ex eb mb [ib] IIC T4, Ex tb IIIC T135°C SIRA 12ATEX5239X
II 2 (2) D Ex tb IIIC T135°C IP66 Db
2
For single TESH Cable
For two TESH Cables
For RTD lead wire
205mm
190mm
50mm
3 mm
8 mm
2
Terminator-LN-Tool
(order separately)
28 mm
33 mm
