Safety 1st Safe Contact Instrucciones página 5

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
• Do not put the battery terminals in short circuit.
• DO NOT PUT the product in water.
• Used batteries must not be burned or thrown out with domestic rubbish but deposited in specialised recycling centres.
• Remove the batteries when the appliance is unused for long periods of time.
• Remove the adapter before replacing the batteries.
3) Features
• Starting up : Establish contact between the units.
To switch on the parent unit and the child unit press the ON/OFF button
on both units will flash green while contacting is being established unless the parents' unit is being charged. Once contact has been
established between the two units, the light will stop flashing and become permanently green.
• Adjusting the volume
To adjust the volume, press the volume increase button ( + ) or volume decrease button ( - ). There are 10 sound levels. Each sound
level is signalled by a beep. When maximum or minimum volume has been reached the unit will beep twice.
•Child unit :
- Search function
This function enables you to find the parent unit. When the child and parent units are connected up with one another press the
button
for one second to activate the search function. The parent unit will give out a sound signal.
Press any button on the parent unit to stop the beeps, except the start/stop button
•Parent unit :
- Recharging the batteries
When the light on the parent unit is showing permanently red and the unit is emitting continuous beeps, it is essential that you
recharge the batteries.
In order to do this, plug the parent unit into the mains (see diagram). The light will flash red during recharging.
For good-quality communication, the parent unit should preferably contain batteries even when it is plugged into the mains.
If the batteries run down at abnormal speed after having been fully charged, replace the rechargeable batteries with new rechar-
geable batteries of the same type.
- Warning that maximum distance has been exceeded or contact has been lost
When the parent unit is too far away or is no longer in contact with the child unit, you will hear continuous warning beeps sounding
from the parent unit. The light on the parent unit will also flash green for as long as the connection is not re-established.
If the parent unit is not working or is switched off while charging, the light on the child unit will flash green.
Be careful: The child unit does not give out a sound signal.
- «VOX» function
Selective system of «VOX» wave emission: Listening on demand.
To activate the VOX facility slide the button towards the «ON» position.
- ON Mode: Listening activated only by the baby's voice, no background noise.
- OFF Mode: Listening activated by any type of noise. Permanent background noise.
To cancel the VOX function slide the button towards the «OFF» position.
- Lights showing tear intensity
Lights are activated according to the intensity of baby's tears. The greater the intensity the greater number of lights will be activated.
The unit provides 3 levels of tear intensity.
4) Function check
At the end of these different stages, please check that the equipment works correctly under real conditions.
III -FEATURES
Light and beeps
Permanently green
Flashing green
Flashing red
Permanently red and
beeps
3 red lights
Warning sound when
conact between the
two units is lost or if
the battery is weak. The
unit gives out a series of
continuous beeps.
Parent
Child
unit
unit
X
X
The units are correctly connected.
One flash per second means that
X
X
the connection between the two
units has been lost.
X
Battery charging.
X
Battery run down.
Lights showing tear intensity.
The greater the intensity the
X
greater number of lights will be
activated.
The connection between the
X
parent unit and the child unit has
been lost.
. Hold it down for 3 seconds, then release it. The light
and the «VOX» button.
Indications
Solutions
-
Make sure the two units are
correctly plugged in.
Move the two units closer to one
another.
-
-
-
Make sure the two units are
correctly plugged in.
Move the two units closer to one
another.
5
Tabla de contenido
loading

Este manual también es adecuado para:

33110027

Tabla de contenido