G Lubrication
BEARINGS
STANDARD: Supplied sealed and pre-lubricated. No lubrica-
tion required.
CHAIN
The drive chain (where applicable) is pre-lubricated from the
manufacturer by a hot dipping process that ensures total lubri-
cation of all components. However, continued proper lubrica-
tion will greatly extend the useful life of every drive chain.
Drive Chain lubrication serves several purposes including:
• Protecting against wear of the pin-bushing joint
• Lubricating chain-sprocket contact surfaces
• Preventing rust or corrosion
For normal operating environments, lubricate every 2080 hours
of operation or every 6 months, whichever comes first. Lubri-
cate with a good grade of non-detergent petroleum or synthet-
ic lubricant (i.e., Mobile 1 Synthetic). For best results, always
use a brush to generously lubricate the chain. The proper vis-
cosity of lubricant greatly affects its ability to flow into the inter-
nal areas of the chain. Refer to the table below for the proper
viscosity of lubricant for your application.
Ambient Temperature
Degrees F
20-40
40-100
100-120
The drive chain's lubrication requirement is greatly affected by
the operating conditions. For harsh conditions such as damp
environments, dusty environments, excessive speeds, or ele-
vated temperatures, it is best to lubricate more frequently. It
may be best, under these conditions, to develop a custom
lubrication schedule for your specific application. A custom
lubrication schedule may be developed by inspecting the drive
chain on regular time intervals for sufficient lubrication. Once
the time interval is determined at which the chain is not suffi-
ciently lubricated, lubricate it and schedule the future lubrica-
tion intervals accordingly.
REDUCERS
MANUFACTURED BY HYTROL:
packing envelope that contains lubrication and maintenance
instructions for Hytrol's gear reducer.
MANUFACTURED BY OTHERS: Refer to their recommenda-
tions.
SAE
ISO
20
46 or 68
30
100
40
150
See separate manual in
G Lubricación
RODAMIENTOS
ESTANDAR: Suministrados sellados y prelubricados. No
requieren lubricación.
CADENA
La cadena motriz ha sido pre-lubricada por el fabricante
mediante un proceso de sumersión caliente que asegura
una lubricación total de todos sus componentes. Sin embar-
go, una lubricación apropiada y continua extenderá su vida
útil considerablemente.
La lubricación de la cadena motriz cumple varios propósi-
tos:
• Proteger contra el desgaste de la unión de pines
de la cadena
• Lubricar las superficies de contacto entre la cadena
y la catarina
• Prevenir la oxidación o corrosión.
En operaciones bajo condiciones ambientales normales,
lubrique cada 2080 horas de operación o cada 6 meses, lo
que ocurra primero. Lubrique con un lubricante sintético (ej.
Mobile 1 sintético) o basado en petroleo no-detergente de
buen grado. Para mejores resultados, siempre utilice una
brocha para lubricar la cadena generosamente. La viscosi-
dad apropiada del lubricante afecta enormente el fluido del
mismo hacia las áreas internas de la cadena. Refiérase a la
siguiente tabla para consultar la viscosidad de lubricante
adecuada para su aplicación.
Temperatura Ambiente
(Grados Fº) (Grados Cº)
20-40
-07 – 04
40-100
04 – 38
100-120
38 – 49
El requerimiento de lubricación de la cadena motriz se vé
afectado
considerablemente por las condiciones de
operación. En condiciones difíciles tales como: ambientes
húmedos, ambientes con polvo, velocidades excesivas, o
temperaturas elevadas, se recomienda lubricar la cadena
con más frecuencia. Lo mejor sería que bajo estas condi-
ciones se establezca un programa de lubricación específico
para su aplicación. Este programa específico puede desar-
rollarse mediante la inspección de la lubricación suficiente
de la cadena motriz en intervalos regulares de tiempo. Una
vez se ha determinado el intervalo en el cual la cadena no
se encuentra suficientemente lubricada, lubríquela y pro-
grame los siguientes intervalos de acuerdo al intervalo
anterior.
REDUCTORES
FABRICADOS POR HYTROL: Diríjase al manual que
viene en el sobre adjunto al transportador, el cual contiene
instrucciones de lubricación y mantenimiento de los
Reductores Hytrol.
FABRICADOS POR OTROS: Refiérase a sus recomenda-
ciones.
SAE
ISO
20
46 o 68
30
100
40
150
27