Ecco EB7800 Serie Instrucciones De Instalación

Ecco EB7800 Serie Instrucciones De Instalación

Baliza giratoria
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

!
WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property damage,
serious bodily/personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety
information.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning de-
vices are essential to ensure the safety of you and those you are seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause
high current arcing, which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that
output performance of the system is maximized and the controls are placed within convenient reach of the operator
so that s/he can operate the system without losing eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in
an air bag deployment area may reduce the effectiveness of the air bag or become a projectile that could cause se-
rious personal injury or death. Refer to the vehicle owner's manual for the air bag deployment area. It is the respon-
sibility of the user/operator to determine a suitable mounting location ensuring the safety of all passengers inside
the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In
use, the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components
(i.e., open trunks or compartment doors), people, vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning sig-
nal. Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before enter-
ing an intersection, driving against traffic, responding at a high rate of speed, or walking on or around traffic lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and
obeying all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and
federal laws and regulations. The manufacturer assumes no liability for any loss resulting from the use of this warn-
ing device.
Specifications:
Voltage: Models EB7810-EB7816: 12 or 24* VDC
Model Number
Size
EB7810
6" dia. x 8.3 height
EB7813
6" dia. x 5.7 height
EB7813-MG
6.6" dia. x 6 height
EB7816
6" dia. x 7.3 height
Current Draw:
1.36 Amps @ 12 VDC, 0.64 Amps @ 24
VDC
Flash Rate:
180 per minute
*See wiring instructions below for 24 VDC systems
Installation & Mounting:
Carefully remove the rotating beacon and examine the unit
for transit damage, broken lamps, etc. If damage is found,
contact the transit company or ECCO. Do not use broken or
damaged parts.
Installation Instructions
EB7800 Series Rotating Beacon
!
Weight
1.70 lbs
When drilling into any vehicle surface, make sure that the area is free
1.20 lbs
from any electrical wires, fuel lines, vehicle upholstery,etc. that could
2.05 lbs
be damaged.
1.55 lbs
CAUTION:
Page 1 of 4
Tabla de contenido
loading

Resumen de contenidos para Ecco EB7800 Serie

  • Página 5: Especificaciones

    Retire cuidadosamente la baliza giratoria y examine la unidad para ver si se ha dañado en el tránsito, si hay luces rotas, etc. Si hay daños, contacte a la compañía de transporte o a ECCO. No use partes rotas o dañadas.
  • Página 6: Baliza Giratoria Con Ensamblaje Magnético: Eb7813-Mg

    Conexión rápida de la baliza giratoria Baliza giratoria con ensamblaje de tres pernos: EB7813 (Consulte la FIGURA 1) (ensamblaje en riel/tubo): EB7810 Estas balizas han sido diseñadas para ser ensambladas en tubo, en un tubo de ¾” y conectadas a una fuente de corriente a través Seleccione la ubicación del ensamblaje para la baliza en una de un conector DIN estándar (Ver FIGURA 2).
  • Página 7: Instrucciones De Cableado

    Instrucciones de cableado: Repuestos y accesorios: ¡Importante! Deshabilite la energía antes de cablear la baliza. Descripción Número de parte El cableado se muestra en la FIGURA 4. Todo el cableado debe Lente de reemplazo, ámbar R5810LA ser de un mínimo de 18 AWG (0.83 mm²). La línea positiva debe tener un fusible de 5 amp, como se muestra.
  • Página 8 Limitación de responsabilidad y garantía limitada del fabricante: El fabricante garantiza que al momento de la compra, este producto cumple con las especificaciones del fabricante para el mismo (disponibles a pedido). El fabricante garantiza además que el presente producto está libre de defectos en sus materiales y en su fabricación.

Tabla de contenido