Timer Operation - Friedrich MW18Y3H Manual De Funcionamiento

TIMER OPERATION

Before using the timer function, be sure that the Remote Controller is set to the correct current time (☞ P.5).
To Use the ON timer or OFF timer
1
Press the START/STOP button (Fig. 6 b8)
(if the unit is already operating, proceed to step 2).
The indoor unit's OPERATION Indicator Lamp (green) (Fig. 3 a5) will light.
2
Press the TIMER MODE button (Fig. 6 b6) to select the
OFF timer or ON timer operation.
Each time the button is pressed the timer function changes in the following
order:
PROGRAM(OFF
The indoor unit's TIMER Indicator Lamp (orange)(Fig. 3 a6) will light.
3
Use the TIMER SET buttons (Fig. 6 b13) to adjust the
desired OFF time or ON time.
Set the time while the time display is fl ashing (the fl ashing will continue for
about fi ve seconds).
button: Press to advance the time.
button: Press to reverse the time.
About fi ve seconds later, the entire display will reappear.
To Use the Program timer
1
Press the START/STOP button (Fig. 6 b8).
(if the unit is already operating, proceed to step 2).
The indoor unit's OPERATION Indicator Lamp (green) (Fig.3 a5) will light.
2
Set the desired times for OFF timer and ON timer.
See the section "To Use the ON timer or OFF timer" to set the desired mode
and times.
About three seconds later, the entire display will reappear.
The indoor unit's TIMER Indicator Lamp (orange) (Fig.3 a6) will light.
3
Press the TIMER MODE button (Fig. 6 b6) to select the
PROGRAM timer operation (OFF
will display).
The display will alternately show "OFF timer" and "ON timer", then change to
show the time setting for the operation to occur fi rst.
●
The program timer will begin operation. (If the ON timer has been selected
to operate fi rst, the unit will stop operating at this point.)
About fi ve seconds later, the entire display will reappear.
About the Program timer
●
The program timer allows you to integrate OFF timer and ON timer operations in a
single sequence. The sequence can involve one transition from OFF timer to ON
timer, or from ON timer to OFF timer, within a twenty-four hour period.
●
The fi rst timer function to operate will be the one set nearest to the current time.
The order of operation is indicated by the arrow in the Remote Controller's Display
(OFF ON, or OFF ON).
●
One example of Program timer use might be to have the air conditioner automati-
cally stop (OFF timer) after you go to sleep, then start (ON timer) automatically in the
morning before you arise.
9315345288_OM.indb 8 9315345288_OM.indb 8
CANCEL OFF ON
ON, OFF ON)
ON or OFF
To Cancel the Timer
Use the TIMER MODE button to select
"CANCEL".
The air conditioner will return to normal
operation.
To Change the Timer Settings
Perform steps 2 and 3.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
SUPER QUIET mode), after making the timer
setting wait until the entire display reappears,
then press the appropriate buttons to change
the operating condition desired.
To Cancel the Timer
Use the TIMER MODE button to select
"CANCEL".
The air conditioner will return to normal
operation.
To Change the Timer Settings
1. Follow the instructions given in the section
"To Use the ON Timer or OFF Timer" to select
the timer setting you wish to change.
2. Press the TIMER MODE button to select
either OFF ON or OFF
To Stop Air Conditioner Operation
while the Timer is Operating
ON
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
SUPER QUIET mode), after making the timer
setting wait until the entire display reappears,
then press the appropriate buttons to change
the operating condition desired.
ON.
En-8
2/24/2010 1:36:24 PM 2/24/2010 1:36:24 PM