Technical Data - V2 TYPHOON Manual De Instrucciones

ANEMOMETER WITH SUN AND
TEMPERATURE SENSOR – REMOTE CONTROL
The TYPHOON sensor detects the sun, wind, and temperature
parameters and transmits them by radio to the remote controller.
If the SUN threshold is exceeded, an OPEN command is sent to
the sunshade, whereas if the WIND threshold is exceeded, a
CLOSE command is sent.
Using 2 buttons and 8 LEDs, the thresholds for the sensors can
be set and the device can be memorized on the controlled
remote controller.
The TYPHOON sensor is compatible with the following devices:
LEX-RM - all versions
LEX-HRM - all versions
LEX-RFE - all versions
CU1 - Version 1.9 or later
CU3 - Version 1.5 or later
CU4 - Version 1.5 or later
CU5 - Version 1.5 or later
To install TYPHOON, carefully read these instructions.
CAUTION: If the system is left unattended for long periods,
we recommended that the sunshade be closed and that
the sun sensor's automatic function be deactivated.

TECHNICAL DATA

Transmission frequency
Protection
Temperature for use
1. DEVICE MEMORIZATION ON REMOTE
CONTROLLERS
1. Move to a position close to the remote controller that will be
controlled
2. Power the device with a temporary cable
3. If the sunshade is controlled with transmitters in the DUO
series, use a remote control that is already memorized in the
controller and proceed as follows:
a. Press SELC on the transmitter a few times, until the LEDs
display the channel memorized (only DUO6 and DUO4)
b. Return the awning to its mid-height
c. Move Switch 1 on the transmitter to the ON position
d. Press and hold down PROG on the transmitter for about 5
seconds, until the motor starts to move
e. Release PROG and the motor will stop
f. Press P1 on TYPHOON for at least 2 seconds (Fig.2)
g. To check that it has been memorized correctly, press P1:
the sunshade should CLOSE. If not, repeat the procedure
4. If the sunshade is controlled with transmitters in the ADLER
series, use a remote control that is already memorized in the
controller and proceed as follows:
CAUTION: If the remote control used has multiple channels,
first select the channel memorized in the controller using C.
a. Press and hold down the UP and DOWN buttons on the
remote control until the motor starts to move in one
direction.
b. Release the buttons and the motor will stop.
434,15 MHz
IP44
-20 ÷ +60 °C
c. Within 8 seconds, press P1 on TYPHOON for at least
2 seconds
d. To check that it has been memorized correctly, press P1:
the sunshade should CLOSE. If not, repeat the procedure.
2. INSTALLATION
CAUTION: For correct operation, please remember that the
sensor must be positioned near the sunshade it protects and in
an area exposed to sun and wind.
The articulated arm should be parallel to the ground and
the blades should be turned downwards (Fig. 3).
PLEASE NOTE: the location selected for installation
should guarantee full and direct illumination of the surface
of the sensor where the solar cells are positioned for the
majority of the day.
Before attaching the device, make sure the radio coverage is
sufficient: put TYPHOON in the position for installation and press
P1. Check that the sunshade closes.
CAUTION: Check that there are no other devices operating on
the same frequency (434.15 MHz) and with continuous
transmission, such as alarms, radio headphones, etc., which may
interfere with the communication between the sensor and the
command controller. Installing more TYPHOON sensors in the
same area could give rise to the same problem.
1. Remove the cover (Fig. 1)
2. Attach the device to the wall using the provided wall plugs
(Fig. 1)
3. Position the articulated arm horizontally with the blades
turned downwards (Fig. 3)
CAUTION: If the articulated arm is not perfectly horizontal there
may be problems detecting the wind speed.
4. Tighten the screw, V1 (Fig. 3), to lock the movement of the
arm