Routine Maintenance - RIB TOUCH Wi-Fi Manual Del Usuario

TO MEMORIZE OTHER TOUCH Wi-Fi
- Press the PROG. TX key of the TOUCH Wi-Fi with microswitch 2 turned
ON => on MASTER Wi-Fi the bicolor EDGE PHOT 2 LED turns from
flashing red to flashing green and a buzzer tone sounds to indicate
proper memorization of the TOUCH Wi-Fi .
- Perform the same procedure for any other TOUCH Wi-Fi (up to a
maximum of 6).
C
HECKING PROPER FUNCTIONING
After the memorization procedure, check proper functioning between the
TOUCH Wi-Fi and the MASTER Wi-Fi as follows:
I
N CASES OF DIFFICULTY
PROBLEM
The strip does not work
FOR OTHER INFORMATION REFER TO THE INSTRUCTION BOOKLET OF THE MASTER Wi-Fi CARD
E
LECTRONIC TECHNICAL CHARACTERISTICS
CERTIFIED EN 13849-2 (2008) NO. 10.027 CATEGORY 2
FREQUENCY
SENSITIVITY
OUTPUT POWER
POWER SUPPLY
INPUT AT REST
MAXIMUM INPUT
MODULATION TYPE
CAPACITY
BATTERY LIFE
CAPACITY OF CONTACTS
WORKING TEMPERATURE
DEGREE OF PROTECTION
DEGREE OF RELATIVE HUMIDITY <93%
T
ECHNICAL MECHANICAL CHARACTERISTICS
STROKE FROM CONTACT TO INTERVENTION (PRE-STROKE)
STROKE FROM INTERVENTION TO MECHANICAL STRIKER PLATE
(BEYOND STROKE)
OPENING TIME OF CONTACTS AFTER INTERVENTION
RECOVERY TIME OF MAXIMUM DEFORMATION
MAXIMUM FORCE APPLICABLE TO THE DEVICE
MAXIMUM SPEED OF DEVICE IN MOTION
*
Using with operators at a speed greater than 0.25 m/s (15 m/min) is a breach of
regulatory provisions.
868,3 MHz
-108 dBm
<25 mW
3 type AA batteries 1.5 V (> 2.7 Ah)
25 µA
13 mA
FSK
20 m in free space without antenna
3 years (type AA)
0,5 A - 24 V c.a. c.c.
-20°C ÷ +60°C
IP44
max 15 mm
min. 40 mm
max 0.1 s
max 0.5 S
max 1 KN
max 0.25 M/S *
- Make sure that when you press the TOUCH Wi-Fi strip with dip 1 ON, the
corresponding bicolor EDGE PHOT 1 LED on the MASTER Wi-Fi Board
turns red for the duration of the pressing action.
The DL2 LED will turn off to indicate interruption of the contact dedicated
to the EDGE input on the motor control panel.
- Repeat the check on all the installed TOUCH Wi-Fi.
Run a functional check on all the installed TOUCH Wi-Fi by activating the
motion of the automation and check that, upon collision with the strip, the
automation stops/inverts its motion.
Check condition of batteries and contact
R
OUTINE MAINTENANCE
Must be carried out every six months, only by authorized personnel in
agreement with the safety rules and with the manufacturer's instructions.
- The TOUCH Wi-Fi safety edge must be kept in efficient working
conditions and in agreement with the manufacturer's instructions.
- Replace the batteries when requested by the system (see the chart "IN
CASE OF DIFFICULTIES" on the MASTER Wi-Fi manual).
- Verify the presence and the possibility to read the initial marking.
- The parts that wear off are mentioned in the chart "Type of items for the
assembly"; eventual replacements must be carried out by an authorized
technician, following the assembly instructions and verification.
1 - Make sure covers (upper and lower ) and aluminum support are in
good condition and not bent out of shape; make sure rubber part is in
good condition and not torn.
2 - Dismantle cover.
3 - Check steel cable to make sure it is in good condition and not frayed;
replace cable is necessary.
4 - Make sure that in conditions of rest, the lever is positioned on the
central limit switch. If it is not, regulate the position by turning the
adjustment screws.
5 - Check condition of upper cover and replace it if it is damaged.
6 - Make sure there are no traces of moisture or foreign bodies and
remove them if there are any.
7 - Keeping the contact of the central limit switch pressed, press the
rubber and make sure the electric circuit is interrupted.
8 - Release rubber strip and make sure electric contact resets.
9 - Put cover back on.
19
19
CHECK
G
B