Tabla de contenido
Idiomas disponibles
Idiomas disponibles
G
B
RELAY AND MOTOR COMMAND
K1 => Opening direction command
K2 => Closure direction command
Q4 => TRIAC - Opening and Closing motor command
Q5 => Blinker command
POINT B
- SETTINGS
DIP 1
(ON) MOTOR ROTATION DIRECTION CHECK
DIP 2
(ON) PROGRAMMING (See Point C)
DIP 1-2 STORING/ERASING RADIO CODES FOR MOTOR
CONTROL (See Point D)
DIP 3
ON - Automatic Closing ENABLED (max 5 min)
OFF - Automatic Closing DISABLED
DIP 4
ON - AUTOMATIC Radio Receiver Command
OFF - STEP BY STEP Radio Receiver Command
DIP 5
ON - AUTOMATIC single pulse command (K BUTT.)
OFF - STEP BY STEP single pulse command (K BUTT.)
DIP 6
ON - Operation in PARK MODE
OFF - Operation in NORMAL MODE
WARNING: The PARK MODE enables or disables some features and
commands:
If NORMAL MODE is enabled, OPEN2 command, OK CLOSE
command and TLC (Traffic Light Control) input, are not enabled.
If PARK MODE is enabled all commands are enabled.
DIP 7
ON - boom arm locking magnet ENABLED (ACQ9080 or ACQ9081
optional cards)
OFF - courtesy light operation ENABLED (ACQ9080 or ACQ9081
optional cards)
If none of the optional card is connected, turn DIP7 to OFF.
DIP 8
ON - in PARK MODE the OPEN2 button is always enabled
OFF - in PARK MODE the OPEN2 button works if there is no vehicle
on the magnetic sensor connected to the TLC input (TLC
contact opened).
DIP 9
ON - safety strip self-test ENABLED
OFF - safety strip self-test DISABLED
DIP 10 ON - after the blackout the boom arm automatically closes
OFF - after the blackout the boom arm remains still on the point it was
when blackout occurred
DIP 11 ON
DIP 12 ON
DIP 13 ON - Blinker operation with intermittent power supply
OFF - Blinker operation with fixed power supply
DIP 14 OFF
DIP 15 OFF
DIP 16 OFF
LED WARNING
DL1 - Programming activated (red)
DL2 - Stop contact (red)
DL3 - Barrier opening (green)
DL4 - Barrier closing (red)
DL5 - Photocells contact (red)
DL6 - Safety strip contact (red)
DL7 - Closing limit switch contact (red)
DL8 - Opening limit switch contact (red)
DL9 - Radio programming activated (green)
POINT C
- TIME PROGRAMMING
1 - Close the barrier completely.
2 - Turn the DIP 2 to ON, the red led DL1 starts blinking.
3 - Press the PROG button, the boom arm opens.
4 - Once opening has been completed, the boom arm stops. The gap of time
between now (stop of the motor) and the next pressing of the PROG button
(see step 5 below) will be then stored as waiting time (max 5 minutes) for
Automatic Closing feature.
5 - Press the PROG button, the boom arm closes and the Automatic Closing
time is stored (see DIP3 function to enable or disable the Automatic Closing
feature).
6 - The red LED DL1 turns off.
7 - Turn DIP2 to OFF.
During Point C procedure, the safety devices (photocells and safety strip)
are active.
POINT D
- RADIO CODE STORING (MAX 60 CODES)
1 - The boom arm must be completely closed.
2 - Turn DIP1 to ON position, the red LED DL1 starts blinking quickly
3 - Immediately, turn also DIP2 to ON position, the red LED DL1 starts blinking
slowly. Each code must be programmed within 10 seconds.
4 - Press one of the buttons on the remote control (usually channel A). If the
remote control is stored correctly green LED DL9 (on the PARK 230V CRX
control board) emits a flash. The 10 seconds' time within storing radio codes
is automatically renewed to allow the string of the next remote control.
5 - To end radio code storing either press PROG button or let 10 seconds pass.
The LED DL1 shall stop blinking.
6 - Turn DIP1 to OFF position.
7 - Turn DIP2 to OFF position.
RADIO CODE ERASING
1 - The boom arm must be completely closed.
2 - Turn DIP1 to ON position, the red LED DL1 starts blinking quickly
3 - Immediately, turn also DIP2 to ON position, the red LED DL1 starts blinking
slowly. Code erasing must be carried out within 10 seconds.
4 - Press the PROG button and hold it for 5 seconds, the total memory erasing
will be indicated by two flashes of the green LED DL9. The red LED DL1
will blink for 10 seconds and it will be possible to store new radio codes
following the Point E procedure described above.
5 - To end radio code storing either press PROG button or let 10 seconds pass.
The LED DL1 shall stop blinking.
6 - Turn DIP1 to OFF position.
7 - Turn DIP2 to OFF position.
RADIO CODE FULL MEMORY TEST
1 - The boom arm must be completely closed.
2 - Turn DIP1 to ON position, the red LED DL1 starts blinking quickly.
3 - Immediately, turn also DIP2 to ON position, the red LED DL1 starts blinking
slowly. If the green LED DL9 flashes six times, it means that the radio code
memory is FULL (maximum codes to be stored 60).
6 - Turn DIP1 to OFF position.
7 - Turn DIP2 to OFF position.
30
30
Tabla de contenido
