Makita PDC01 Manual De Instrucciones página 13

Overheat protection
When the tool or battery is overheated, the tool stops
automatically. In this case, let the tool and battery cool
before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
Power button and battery indicator
CAUTION:
Make sure that the tool or machine
is turned off before turning on the unit. Otherwise,
the tool or machine may start suddenly and cause an
injury.
► Fig.5: 1. Main power lamp 2. Power button
To turn the power on, press the power button. The main
power lamp lights up in green. To turn the power off,
press the power button for a few seconds.
NOTE: If the unit and connected tool or machine are
left unattended for 8 hours, the unit automatically
turns off.
If the main power lamp blinks in green, the adapter is
not connected to the unit, or the batteries are empty. In
this case, connect the adapter to the unit, or charge the
batteries. If the lamp keeps blinking in green, refer to
the troubleshooting.
If the main power lamp blinks in red and green alter-
nately, turn the power off, and then turn the power on.
If the main power lamp keeps blinking in red and green
alternately after turning the power on, ask your local
Makita Authorized Service Center for repair.
NOTE: If you turn on the main power switch of the
tool or machine just after turning on the portable
power pack, the indicator(s) on the tool or machine
may show that the protection system is working. In
this situation, start the tool or machine once. If the
indicator(s) turns off, you can operate the tool or
machine. If the indicator(s) is still on, check the main
power lamp of the portable power pack and refer the
section "TROUBLESHOOTING" to solve the problem.
Press the power button to indicate the remaining battery
capacity. The indicator lamp that corresponds to each
battery port lights up for approximately 5 seconds.
Indicator lamps
Lighted Off
Remaining
capacity
Blinking
50% to 100%
0% to 50%
Charge the
battery.
NOTE: The indicator lamps for remaining battery
capacity is just for a reference. The actual bat-
tery capacity may differ depending on the usage
conditions.
NOTE: If the tool or machine has indicator lamps for
remaining battery capacity, do not refer to the indica-
tor lamps of the tool or machine but to the indicator
lamps of this unit.
Low battery indication lamp of
Adapter for 36 V - 40 Vmax
Optional accessory
This adapter features the indication lamp that notifies
you of low or no battery capacity.
When the indication lamp is blinking, the remaining
battery capacity gets low.
When the indication lamp lights up, the battery protec-
tion system is activated.
NOTE: Depending on the battery status, the tool/
machine may automatically stop without blinking the
indication lamp during continuous operation.
NOTE: The timing when the indication lamp blinks
varies depending on the ambient temperature and
battery status.
NOTE: The indication lamp does not lights up even
when the battery cartridge currently used is depleted.
The indication lamp lights up while PDC01 is switch-
ing the battery cartridges to use.
► Fig.6: 1. Low battery indication lamp
Using the adapter pocket
CAUTION:
Do not use this unit with the cord
fixed using the hook and loop fastener of the
adapter pocket.
You can put the adapters into the adapter pocket as
shown in the figure.
► Fig.7: 1. Adapter 2. Adapter pocket
► Fig.8: 1. Adapter 2. Adapter pocket
ASSEMBLY
CAUTION:
Always be sure that the unit is
switched off and the battery cartridge is removed
before carrying out any work on the unit.
Assembling the unit
1. Attach the battery box to the base plate as shown
in the figure. Be sure to lock the levers on both sides of
the base plate after attaching the battery box.
► Fig.9: 1. Lever 2. Battery box 3. Base plate
CAUTION:
Make sure that the battery box is
securely fixed to the base plate, and locked with
levers. Otherwise, the battery box may fall when you
wear the unit or use the unit, and cause an injury.
13 ENGLISH