Power Source - Craftsman 351.211930 Manual De Usuario

TOOL REST
Parts to be assembled should be located and accounted for
(See List and Figure 3).
A _;_18 x 1_" Carriage bolt, 2 each
B Tool rest, 2 each
C _" Fiat washer, 6 each
D _" -18 Hex nut, 2 each
E Bracket, 2 each
F _-18 x ¾" Hex bolt, 4 each
c
E
Figure 3 -Tool Rest
Refer to Figures 1, 2 and 3, pages 3 and 4.
IMPORTANT: Do not attempt assembly if parts are missing.
Use this manual to order replacement parts.
STAND ASSEMBLY
Refer to Figure 1, page 3.
NOTE: Finger tighten bolts and nuts until assembly is
complete. Then tighten all fasteners securely.
,, Place top (H) on the flat surface up side down..
,, Attach 4 leg sections (B) to the top using carriage bolts (D),
washers (E) and nuts (F).
,, Attach 2 short braces (C) and 2 long braces (G) to the
ends of already assembled leg brackets using carriage
bolts (D), washers (E) and nuts (F)
° Attached remaining 4 leg sections (B) to the braces using
carriage bolts (D), washers (E) and nuts (F)..
° Attach foot pads (A) to the end of each leg..
,, Turn the stand side up and position on the fioor..
= Adjust stand position so all legs are contacting the floor
and are positioned at similar angles to the floor
,, Fully tighten all bolts.
NOTE: Stand should not rock after all bolts are tightened°
MOUNT GRINDER
Locate bag with following hardware:
8-1.25 x 45mm Hex bolt, 4 each
8mm Flat washer, 8 each
8mm Lock washer, 4 each
8-1.25mm Hex nut, 4 each
, Place grinder on the top of the stand
,, Align mounting holes in grinder's base with siets on stand's
top.
,, Use 8-1..25 x 45mm hex bolts with 8mm flat washers, Bmm
lock washers and 8-1 ..25ram hex nuts to secure grinder to
stand top
EYESHIELD ASSEMBLY
Refer to Figure 2, page 3
,, Fasten spark guard (K) to wheel guard using hex bolt (J),
lock washer (i), flat washer (H) and serrated washer (A)
NOTE: Serrated washer must be placed between spark guard
and wheel guard surfaces for added stability
,, Remove pan head screws (B) from eyeshie]d assembly.
,, Mount left upper eyesh[eld bracket (C) to eyeshield (E)
using pan head screws (B) and lower eyeshield bracket
(U),,
NOTE: Left upper eyeshield bracket is stamped "C' for
identification.
° Slide knob (G) through 6mm fiat washer (F) and through
hole at top of spark guard (K) and fasten into upper
eyeshield bracket (C)
- Locate eyeshield in desired position for protecting operator
and tighten knob
- Mount right eyeshield assembly in a similar manner.
TOOL REST ASSEMBLY
Refer to Figure 3, page 3
° Attach bracket (E) to wheel guard using hex bolts (F) and
fiat washers (C)o
° Tighten bolts finger tight
° SIide _,1,-18x 1%" carriage bolt (A) into square hole in tool
rest bracket (E)
• Slide tool rest (B) onto carriage bolt from the inside of tool
rest as shown in Figure 3.
, Slide _" flat washer (C) and _I,"-18 hex nut (F) onto
carriage bolt..
• Tighten nut finger tight
• Position too_ rest so that distance between tool rest and
grinding wheel is tess than _,".
• Secure all nuts and bolts
- Mount the opposite side tool rest in a similar manner.
Refer to Figures 4 and 5.
POWER SOURCE
WARNING: Do not connect grinder to the power source until
all assembly steps have been completed,
The motor is designed for operation on the voltage and fre_
quency specified,, Normal loads will be handled safely on volt-
ages not more than 10% above or below specified voltage,
Running the unit on voltages which are not within range may
cause overheating and motor burn-out. Heavy loads require
that voltage at motor terminals be no tess than the voltage
specified on nameplate.