Tabla de contenido
Idiomas disponibles
Idiomas disponibles
KEY DIMENSIONS AND SPECIFICATIONS
Description
Electrical Requirements
Max. Water Pressure
Dimensions
Net Weight
CHOOSE THE PROPER LOCATION
WARNING
•
This washer is heavy. Two or more people are required
when moving and unpacking the washer. Failure to do so
may result in damage to property or serious bodily harm.
•
Store and install the washer where it will not be exposed
to temperatures below freezing or exposed to outdoor
weather conditions. Failure to follow this warning can
cause serious injury, fire, electric shock, or death.
•
Properly ground washer to conform with all electric
governing codes and ordinances. Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
•
To reduce the risk of electric shock, do not install the
washer in humid spaces. Failure to follow this warning
can cause serious injury, fire, electric shock, or death.
•
To ensure proper air flow, do not block the large
opening on the bottom of the washer with carpeting or
other materials.
•
Do not remove ground prong. Do not use an adapter
or extension cord. Plug into a grounded 3-prong outlet.
Failure to follow this warning can cause serious injury,
fire, electric shock, or death.
NOTE: Installing the washer in a humid space, or installing
or storing the washer where it will be exposed to the
weather or freezing temperatures, may result in rust or
other damage that is not covered by the product warranty.
Power Outlet
•
The power outlet must be within 60 in. (1.5 m) of either
side of the washer.
•
The appliance and outlet must be positioned so that the
plug is easily accessible.
•
Do not overload the outlet with more than, one
appliance.
•
The outlet must be grounded in accordance with current
wiring electric codes and regulations.
•
Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation of
the product owner to have a proper outlet installed by a
qualified service technician.
FLOORING
•
To minimize noise and vibration, the washer MUST be
installed on a solidly constructed floor. See the NOTE at
right.
•
Allowable slope under the entire washer is a maximum
1 in. difference from side to side or from front to back.
•
Installing on carpeting and soft tile surfaces is not
recommended.
•
Never install the washer on a platform or weakly
supported structure.
INSTALLATION REQUIREMENTS
Front-Loading Washer
120 VAC, 60 Hz
20 - 120 psi (138 - 827 kPa)
27 in. (W) X 29 3/4 in. (D) X 38 11/16 in. (H), 52 in. (D, with door open)
68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 132.2 cm (D, with door open)
202.8 lbs (92 kg)
CLEARANCES
1
22
/
in
4
(56.6 cm)
To ensure sufficient clearance for water lines and airflow,
allow minimum clearances of at least 1 in. (2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or floor moldings that may increase the
required clearances.
1 in.
(2.5 cm)
Allow at least 22
the washer to open the door.
NOTE: The floor must be strong and rigid enough to
support the weight of the washer, when fully loaded,
without flexing or bouncing. If your floor has too much flex,
reinforce it to make it more rigid.
A floor that is adequate for a top-loading washer may
not be rigid enough for a front loading washer, due to the
difference in the spin speed and direction. If the floor is not
solid, your washer may vibrate and you may hear and feel
the vibration throughout your house.
7
4 in
3
29
/
in
4
(10 cm)
(75.6 cm)
52 in
(132.2 cm)
27 in
1 in.
(68.6 cm)
(2.5 cm)
1
/
in. (56.6 cm) in front of
4
Capítulos
Tabla de contenido
Solución de problemas
