Using The Saw - ALPHA-TOOLS TK 200 Manual De Instrucciones

Sierra circular de mesa
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21
Anleitung TK 200
31.10.2001 13:48 Uhr
GB
7. Assembly
Always pull out the power plug before carrying
out any maintenance or conversion work.
7.1 Fitting the saw blade (Fig. 2)
Caution! Pull out the power plug.
Undo the two screws (16).
Take off the chip box (21).
Undo the nut (17) with a size 19 wrench on the
nut itself and a second fork wrench (size 8) on
the motor shaft (a) to apply counter-pressure.
Caution! Turn the nut in the direction of rotation
of the saw blade (4).
Take off the outer flange (19) and pull the old
saw blade (4) off the inner flange (20) by
dropping the blade at an angle.
Clean the mounting flange (19 / 20).
Fit the new saw blade in reverse order.
Caution! Note the direction of rotation (see arrow
on the saw blade).
7.2 Adjusting the splitter (Fig. 3)
Undo the nut (14) from the screw (15) and
remove the saw blade guard (2).
Take out the table insert after removing the 6
countersunk head screws (22).
Slacken the screws (23) in order to adjust the
splitter (5).
Adjust the splitter (5) so that it forms a line with
the saw blade (4) and the distance between the
saw blade (4) and the splitter (5) equals
3 - 5 mm.
Retighten the splitter.
Refit the table insert and the saw blade guard.
Important!
The splitter has to be adjusted each time the saw
blade is changed.
7.3 Fitting the saw blade guard
Mount the saw blade guard (2) on the splitter (5)
and align.
Use the screw (15) and the nut (14) to fasten the
saw blade guard (2) to the splitter (5).
7.4 Adjusting the brake (Figure 4)
You will needed to adjust the brake if the maximum
braking time of 10 seconds is exceeded.
14
Seite 14
To do so, turn the screw (a) clockwise so that the
brake lining (b) is pressed with greater force against
the saw blade. Keep on adjusting the brake until the
braking time equals approx. 5 seconds.

8. Using the saw

8.1 Switching on and off (Fig. 5)
The saw can be switched on by pressing the
green pushbutton (a).
Wait for the saw blade to reach its maximum
speed before beginning to saw.
The red pushbutton (b) has to be pressed to
switch off the saw.
8.2 Parallel stop (Fig. 6)
The parallel stop (7) has to be used when slitting
wood pieces.
Slide the parallel stop (7) to the left side of the
saw table (1).
The parallel stop (7) can be set to the required
dimension with the help of the scale fitted to the
saw table (1).
Fix the parallel stop with the two knurled screws
(12).
8.3 Adjusting the angle (Fig. 7)
Undo the two knurled screws (24).
Swing the saw table (1) to the right and tilt to the
required angle using the scale on the angle
support (a).
Retighten the two knurled screws (24).
Important: Always tighten the knurled screws
securely to prevent the saw table dropping
accidentally.
9. Sawing operations
After each new adjustment it is advisable to carry
out a trial cut in order to check the set
dimensions.
9.1 Cutting narrow workpieces
(width less than 120 mm) (Fig. 8)
Adjust the parallel stop (7) to the width of
workpiece you require.
Tabla de contenido
loading

Este manual también es adecuado para:

43.402.01

Tabla de contenido