Zodiac Pool Systems JandyPro Serie Manual De Instrucciones página 11

Jandy Pro Series Underwater Pool and Spa White Lights | Installation Manual
®
Section 7. Replacing the Lamp
WARNING
Always disconnect power to the pool or spa white
light at the circuit breaker before servicing the light.
Failure to do so could result in death or serious
injury to installer, serviceman, pool or spa users or
others due to electrical shock.
1. Turn off the main electrical switch or circuit
breaker, as well as the switch, which operates the
underwater light.
2. Be sure to have the following items:
• A new lens gasket (P/N R0451101 for Jandy
Pro Series Pool Light and P/N R0400501 for
Jandy Pro Series Spa Light).
• One (1) new lamp. See Table 1 for
specifications.
WARNING
Replace the lamp with one of the same type and
wattage. Failure to replace the lamp with one of
the same type will damage the light assembly and
may cause an electrical hazard resulting in death
or serious injury to pool or spa users, installers, or
others due to electrical shock, and may also cause
damage to property. Be sure the power is switched
OFF before removing or installing lamps. Allow lamp
to cool before replacing.
3. To remove the light assembly, unscrew the special
pilot screw at the top of the face ring, remove light
assembly from niche and gently place assembly on
the deck. It is not necessary to drain down the pool
or spa. See Figure 7.
Jandy Pro Series Model
Pool/Spa White Light 12 Volt AC
Pool White Light
120 Volt AC
Pool White Light 12 Volt AC
Pool White Light 120 Volt AC
Spa White Light 120 Volt AC
Table 1. Lamp Specifications
Fixture Lamp
Voltage Voltage Wattage
12V 100 Watt
120V 300 Watt
12V 300 Watt
120V 500 Watt
120V 60 Watt
4. Disassemble the light fixture and replace lamp as
follows:
Be sure to keep the special pilot screw from this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided
could create an electrical hazard, which could result
in death or serious injury to pool or spa users,
installers or others due to electrical shock.
a. Loosen the eight (8) Phillips head screws for pool
light or the six (6) Phillips head screws for spa
light to allow the bottom clamp to be removed
from the face ring assembly. Do not remove the
screws or the retaining rings. The retaining rings
prevent the screws from falling free from the top
clamp and also aid in ease of assembly.
b. Remove the lower clamp, the face ring assembly,
the glass lens, and the gasket from the fixture.
Remove the gasket from the lens. Refer to Section
9, Exploded View and Replacement Parts.
c. Install new lamp.
Risk of Electrical Shock or Electrocution. Always
install a new lens gasket whenever disassembling
the light (for Jandy Pro Series Pool Light Gasket
P/N R0451101 and for Jandy Pro Series Spa Light
Gasket P/N R0400501). Failure to do so may permit
water to leak into the assembly, which could cause:
(a) An electrical hazard resulting in death or serious
injury to pool or spa users, installers, or others
due to electrical shock, or
(b) Breakage of the lamp or lens, which likewise
could result in serious injury to pool or spa users,
installers, or bystanders, or in damage to
property.
Lamp
Lamp Type
R20 Flood
R40 Flood
R40 Flood
R40 Flood
R20 Flood
PAGE 11
ENGLISH
WARNING
WARNING
Qty. per Lamp Kit
Fixture Part Number
1 R0450501
1 R0450502
1 R0450503
1 R0450504
1 R0450505