General Safety Information; Installer Responsibilities - RIDGID AdvanTEXT RSA2AT Instrucciones De Inicio Rapido

Model RSA2AT – Operating Instructions and Parts Manual

GENERAL SAFETY INFORMATION

Electric shock hazard. ALWAYS use a licensed
electrician. ALWAYS apply a fixed lock/tag
before servicing. ALWAYS comply with national and local
electric codes. ALWAYS use the system indoors in a well
ventilated area. NEVER walk on wet floor until power is
disconnected. NEVER remove the ground prong from the
plug. NEVER use an extension cord. NEVER use device if dropped
or damaged - contact customer service at 1-877-9RIDGID.
NEVER allow children
to use this product.
Do NOT expose to rain or snow.
•
• Do NOT disassemble.
Ensure batteries are installed correctly.
Improper polarity could result in equipment
damage
Do NOT mix different batteries. Doing so
will reduce overall performance and may
cause battery leakage or rupture. When replacing batteries, always
replace all 4 at the same time.
Do NOT mix different battery brands. Doing
so will reduce overall performance and may
cause battery leakage or rupture. We recommend using the same
type of batteries within a device.
SAFETY SYMBOLS AND WARNING LEVELS
This information is provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help recognize this
information, observe the following warnings.
Danger indicates an imminently hazardous
situation which, if NOT avoided, WILL result in
death or serious injury.
Warning indicates a potentially hazardous
situation which, if NOT avoided, COULD result
in death or serious injury.
Caution indicates a potentially hazardous
situation which, if NOT avoided, MAY result in
minor or moderate injury.
Notice indicates important information, that if
NOT followed, MAY cause damage to
equipment.
DANGER! Do NOT operate pump or this cellular device
in explosive atmospheres, such as in the presence of
flammible liquids, gases, or dust. Pump motors and
electronics create sparks whick MAY ignite the dust or
fumes.
This is the safety alert symbol. it is used to alert you to
potential bodily injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.

INSTALLER RESPONSIBILITIES

INSTALLER, PLEASE LEAVE THIS MANUAL FOR THE
OWNER WHEN INSTALLATION HAS BEEN COMPLETED.
OVERVIEW OF SAFETY GUIDELINES AND
INSTALLER RESPONSIBILITIES
This device uses electricity in the presence of water,
therefore your safety and the safety of others depend
on you therefore, you MUST read and understand this
manual. If you have questions or do not understand
the information presented in this manual, please call
1-877-9RIDGID.
Most incidents are caused by failure to observe basic
safety rules or precautions. You must be alert to potential
2
.
Ridge Tool Company
hazards. You must have the necessary training, skills, and
tools to perform these functions. RIDGID Pumps cannot
anticipate every possible circumstance that might involve
a potential hazard. Therefore, the warnings in this manual
are not all inclusive. If a tool, procedure, work method or
operating technique that is not specifically recommended
by RIDGID Pumps is used, you must satisfy yourself that
it is safe for you and for others. You should also ensure
that the product will not be damaged or be made unsafe
by the operation, lubrication, maintenance or repair
procedures that you choose.
Chemical Hazard. In the event of
bodily contact, immediately rinse
with cool running water for at least 15 minutes. Seek
medical attention immediately after rinsing.
CALIFORNIA PROPOSITION 65
This product or its power cord MAY contain
chemicals, including lead, known to the State
of California to cause cancer and birth defects or other reproductive
harm. Wash hands after handling.
GETTING TO KNOW YOUR AdvanTEXT DEVICE
(FIGURE B)
1. Status Light - See page 6 for Light Blinking Pattern
Definitions
2. Low Battery Light - See page 6 for Light Blinking
Pattern Definitions
3. ON/OFF/MUTE - Press the button 1 time to mute the
device and 1 time to un-mute the device. Press and
hold for 3 seconds for ON/OFF
4. PUSH TO TEST - Press the button 1 time to test
device and receive a text message.
5. Tether Float Sensor Light - This light blinks when the
Tether Float is activated. (Sewage alarm only)
6. Lower Float Water Sensor Light - This light blinks
when the lower float is activated.
7. Upper Float Water Sensor Light - This light blinks
when the upper float is activated.
8. Sensor Ports - The Dual float sensor (8a) or Tether
Float (8b) plugs in these ports. See (Figure B)
1
2
3
4
5
6
7
8
Figure B
Use of this device and the ability to send and
receive texting alerts in the event of an
emergency are contingent upon an active cellular service.
+
8a
8b
Sump Alarm model shown