Tabla de contenido
Idiomas disponibles
Idiomas disponibles
9. With the mounting plate ( a) t oward the
motor and holding the chain i nplace o n
thebar, feed bar a nd chain i nto the jaw,
angling over the barlocating pins ( d) and
engaging
the chain o nthe drive sprocket
(16) (See F ig I).There islittle excess chain
length, therefore,
thechain m ust be
properly fitted inthebar s lot t oprovide
enough extra c hain t obepulled o ver the
drive sprocket.
10. C heck ifallparts a re seated properly (See
Fig J).
11. R efit and tighten thechain t ensioner bolt.
Note t hecam (e) ofthe tensioner will
engage the projecting
tab(f)ofthe bar
mounting plate a nd push t he bar o utward
totension thechain, check forcorrect
tension (See A DJUSTING
THE
CHAIN
TENSION).
12. Close the access cover and remove the
lock pin.
CHECKING
THE AUTOMATIC
OILER
The JawSaw
uses a much lower chain speed
than a conventional
chainsaw so it needs
much less oil.
However
it is very important
that it always has
oil.
Check the oil level window
(5) and refill as
necessary.
During operation,
periodically
check the
chain and bar. A slight oil presence should
be
visible.
If the chain and bar appear completely
dry, then remove the bar and chain (see
previous
section) to ensure the bar oil hole is
not blocked.
Ifthe oil hole is clear, there is oil in the tank
and still no oiling ofthe
chain is visible -
contact Worx customer
service (contact 1-866-
354-9679).
WARNING:
Do not push the rear handle
repeatedly when the saw is not cutting.The
oil
will be bumped
out when pushing the handle
whatever
the motor runs or not.
I, UBRICATION
|MPORTANT:
The
JawSaw
is shipped
with
an
empty
oi| ta,k.
it is esse,tia|
to fill with
chai,
oil before
use.
Mr
a,d
__
chain
oil of any
brand
can
he used.
Never
operate
the
JawSaw
without
chain
oi| or an
empW
tank
as this
wi||
result
in poor
cutting
performance,
motor
overload
and
possible
hum-out.
FILLING
OIL TANK:
UNPLUG
THE TOOL UEFORE FILLING
WITH
OIL.
1. Fill oil bottle with bar oil. (See Fig. K)
2. Rest the JawSaw with the oil filler (6) facing
u pwa rd
3. Lift the rubber oil filler flap (g) open.
4. Use bottle to fill oil reservoir. (See Fig. L)
5. Close the rubber oil filler flap by pressing
the plug part of the flap into the oil filler to
seal. (See Fig. M)
_
MPORTANT:
Use only the
recommended
oil to avoid damage
to the JawSaw. Never use recycled/old
oil.
Use of non approved
oil will invalidate
the
warranty.
OPERATION
PREPARE
YOUR
JAWSAW
FOR
USE
_
ARN|NO:
Read
and
understand
a||
instructions.
Fai|ure
to re|low
a||
instructions
listed
may
result
in
electric
shock,
fire
and/or
serious
persona|
injuW.
_
ARNING:
Sharp
moving
h|ade.
To prevent
accidental
operation,
ensure
that
the
too|
is disconnected
from
the
power
source
before
performing
the
foi|owing
operations,
failure
to
do
this
could
resuk
in serious
persona|
injury.
_
AUTION:
Sharp
moving
blade.
Always
wear
protective
gloves
when
installing
or removing
the
chain,
the
chain
is sharp
and
ca,,
cut
you
when
it is not
running.
ATTACHING
EXTENSION
CORD
1. To prevent disconnection
of appliance
cord, secure extension
cord to extension
cord retainer.
2. An extension
cord retainer is supplied to
reduce strain on the power cord.To use
this feature, form a loop atthe
end of the
extension
cable and bring this through
the
Tabla de contenido
